my E Mesh water pipe.....

[starway7]

This creation is almost done...

A hollow bic pen body will temporarily do for a pipe stem for now ..untill later i will glue on a permanant stem socket and with that use a longer bigger diamiter stem....

This mini E mesh vape has plenty of air flow..using the.... WOTOFO profile vents...

This little water pipe.. [using distilled water].. is very compact and adds to the cooling effect.. and a water trap for unwanted airborn particles...

 

[starway7]

This creation is almost done...

A hollow bic pen body will temporarily do for a pipe stem for now ..untill later i will glue on a permanant stem socket and with that use a longer bigger diamiter stem....

This mini E mesh vape has plenty of air flow..using the.... WOTOFO profile vents...

This little water pipe.. [using distilled water].. is very compact and adds to the cooling effect.. and a water trap for unwanted air born particles...

forgot to say.... im using [ adhesive backed industrial strength velcro] strips.. so when i put the unit together ...[i lock the two together using the velcro strips] now its like one compleate compact vapeing unit...

To.. re load.. spice into unit... carefully pull the two apart /.. [seperating the velcro] then remove the atomizer cap and reload the spice...

To put back together...align the tubing connection [with top of red atomizer] then carefully push the two together ...re locking the velcro! that simple!

My mod box is a ...[75 watt joytech.. e VTC Mini...[two years old] ...with a 18650 battery...

 

[potnoble]

That looks cool!!!
Hope you like it alot.

 

[Th3_tRuTh]

This is brilliant, nice work!

 

[starway7]

That looks cool!!!
Hope you like it alot.

Thanks! im not done yet! im adding a brass pipe stem...and somekind of mouth peice...


Im also replacing the white plastic pick up stem in bottel with brass....

Thinking about putting in a stainles steel ..[splash screen].. in middle of bottle.... in case i pull to hard to keep the water from splashing too high up near the stem....

Normally ..i wouldent pull that hard ..just gentle ] and no splash problem......

Would like to find decals to put outside of bottle [[that look like jungle vines and leaves....]

When i first try it...i will drink a little rue tea first...then see how a low dose of spice effects it...

Then slowly increase the spice to a comfortable level....


forgot to ask ...has anyone tryed the vapouasca route with the direct E mesh yet...?

 

[starway7]

Thanks!

Im still working on this mini direct E mesh W pipe...

Its narrower than a mighty vape...very compact...

 

[Voidmatrix]

That's pretty damn awesome! That's using your noodle:grin: . Let us know how it works.

One love

 

[starway7]

That's pretty damn awesome! That's using your noodle:grin: . Let us know how it works.

One love

Ive tryed it three times ... in low doses ... on direct e mesh.....it works great...within 3 seconds a thick white vapor rises out of the water.. and gets pulled in quickly!

Just have to be carefull not to knock it over because a small amount of water [if knocked over] can run back onto the steel mesh...but by then... your finger is off the button.... and should not short anything out... and just simply remove atomizer...and place in front of fan .. and let dry or sunlight in window..

When taking a hit of the light..just have a friend take the pipe from you ...or if alone... simply take a hit without picking the pipe up with long draw stem...

i thought about installing a one way valve in the copper tubing ..but dont want to restrict the flow...

For those who want to know how i bent the copper tubing...you can use a ..[tubeing bender]..but i

filled the copper tubing with table salt ..[[you can also use sand]...packed it tight with a

metal rod. with booth ends of the tubbing blocked off...


Then... i could bend the copper at a very sharp angle without kinking it...

The little clear plastic bottle can now be found ...at Wall Mart..as well as the industrial adhesive backed velcro... [since the bottle was plastic]... i could easily bore a hole into it with sharp knife tip...

Getting all the connections to be air tight..was just a matter of making the holes fit tight around the tubing...