Members of the previous forum can retrieve their temporary password here, (login and check your PM).

Reply to thread

Message

Thank you endlessness for that link. It's exactly what I was trying to explain, only they broke it down in finer detail. =) As for the obviousness of the subject, it's not always that obvious to those still figuring it out. It's good to have the information available for those who seek it, because everyone figures things out at a different pace.

Alright so the DMT I use is in the white crystal form. It comes from MHRB, specifically Mimosa Tenuiflora, that comes in a fine powder. I do an A/B extraction using distilled water, Hydrochloric Acid for the acidic extraction, and Sodium Hydroxide for the basification. The ph's i use are 1.3/1.4 for the acidic solution, and 11.7/11.8 for the basic solution. To pull the DMT from the basic solution I use VM&P Naptha, and I evaporate it leaning the dish a little to produce more concentrated crystals. After fine tuning this process I have turned what others have call a month process into something you can do within a couple days. I do not heat the solutions during any part of the process, everything is at room temperature. After every stir of the jars, when the ph is perfect, the layers are completely separated within 30 minutes or less, making the process take a fraction of the time. I've completed a batch in a lil over 24 hours once, just to see if I could do it. =) I hope others are having the same success I am, and if not then try to figure out how to fine tune your process to it's most fluent ph's.

lol And I wasn't really implying anyone was making anything 50% pure (but you never know), I was just using it as an example of the ratio.

When it comes to smoking DMT, I used to put it on top of my favorite herb and kinda melt it in before fully ripping it. I've tried freebase, and would rather not do it that way, because it can be harsh at times and I'd much rather smoke it in herb form. Now that I've discovered changa, I don't think I'll do it any other way from now on, but you never know. =)

Last but not least, I would like everyone to understand that I am a "regular" high school drop out, with nothing more than a GED, not much chemical knowledge, have never taken any classes on scientific processes, and attain all my insight and knowledge from personal experience, and the will to understand All. It is in us all if we have the Will to know the information, and Be it. =D

<blockquote data-quote="thatcrazyguywhoknowsalot" data-source="post: 3437514" data-attributes="member: 9288">Thank you endlessness for that link. It&#039;s exactly what I was trying to explain, only they broke it down in finer detail. =) As for the obviousness of the subject, it&#039;s not always that obvious to those still figuring it out. It&#039;s good to have the information available for those who seek it, because everyone figures things out at a different pace. Alright so the DMT I use is in the white crystal form. It comes from MHRB, specifically Mimosa Tenuiflora, that comes in a fine powder. I do an A/B extraction using distilled water, Hydrochloric Acid for the acidic extraction, and Sodium Hydroxide for the basification. The ph&#039;s i use are 1.3/1.4 for the acidic solution, and 11.7/11.8 for the basic solution. To pull the DMT from the basic solution I use VM&amp;P Naptha, and I evaporate it leaning the dish a little to produce more concentrated crystals. After fine tuning this process I have turned what others have call a month process into something you can do within a couple days. I do not heat the solutions during any part of the process, everything is at room temperature. After every stir of the jars, when the ph is perfect, the layers are completely separated within 30 minutes or less, making the process take a fraction of the time. I&#039;ve completed a batch in a lil over 24 hours once, just to see if I could do it. =) I hope others are having the same success I am, and if not then try to figure out how to fine tune your process to it&#039;s most fluent ph&#039;s.lol And I wasn&#039;t really implying anyone was making anything 50% pure (but you never know), I was just using it as an example of the ratio.When it comes to smoking DMT, I used to put it on top of my favorite herb and kinda melt it in before fully ripping it. I&#039;ve tried freebase, and would rather not do it that way, because it can be harsh at times and I&#039;d much rather smoke it in herb form. Now that I&#039;ve discovered changa, I don&#039;t think I&#039;ll do it any other way from now on, but you never know. =)Last but not least, I would like everyone to understand that I am a &quot;regular&quot; high school drop out, with nothing more than a GED, not much chemical knowledge, have never taken any classes on scientific processes, and attain all my insight and knowledge from personal experience, and the will to understand All. It is in us all if we have the Will to know the information, and Be it. =D</blockquote>

[QUOTE="thatcrazyguywhoknowsalot, post: 3437514, member: 9288"] Thank you endlessness for that link. It's exactly what I was trying to explain, only they broke it down in finer detail. =) As for the obviousness of the subject, it's not always that obvious to those still figuring it out. It's good to have the information available for those who seek it, because everyone figures things out at a different pace. Alright so the DMT I use is in the white crystal form. It comes from MHRB, specifically Mimosa Tenuiflora, that comes in a fine powder. I do an A/B extraction using distilled water, Hydrochloric Acid for the acidic extraction, and Sodium Hydroxide for the basification. The ph's i use are 1.3/1.4 for the acidic solution, and 11.7/11.8 for the basic solution. To pull the DMT from the basic solution I use VM&P Naptha, and I evaporate it leaning the dish a little to produce more concentrated crystals. After fine tuning this process I have turned what others have call a month process into something you can do within a couple days. I do not heat the solutions during any part of the process, everything is at room temperature. After every stir of the jars, when the ph is perfect, the layers are completely separated within 30 minutes or less, making the process take a fraction of the time. I've completed a batch in a lil over 24 hours once, just to see if I could do it. =) I hope others are having the same success I am, and if not then try to figure out how to fine tune your process to it's most fluent ph's. lol And I wasn't really implying anyone was making anything 50% pure (but you never know), I was just using it as an example of the ratio. When it comes to smoking DMT, I used to put it on top of my favorite herb and kinda melt it in before fully ripping it. I've tried freebase, and would rather not do it that way, because it can be harsh at times and I'd much rather smoke it in herb form. Now that I've discovered changa, I don't think I'll do it any other way from now on, but you never know. =) Last but not least, I would like everyone to understand that I am a "regular" high school drop out, with nothing more than a GED, not much chemical knowledge, have never taken any classes on scientific processes, and attain all my insight and knowledge from personal experience, and the will to understand All. It is in us all if we have the Will to know the information, and Be it. =D [/QUOTE]