Algernop_Clone
Rising Star
My apologies if this is out there. I searched and may have missed it, and if so would love a link. That out of the way...
I'm planning on using the Q21Q21 Tek 1 with D-Limonene. I have powdered MHRB and chipped (very thin) Acaria Confusa root bark. I have two specific questions. Namely:
Volume. The tek calls for 30g-250g powdered MHRB, with 30g recommended for newbies. I'll start small (thinking 30g-50g), however if doing a larger batch (125g to 250g), what size vessels do you need for the volume? Would getting one 1000ml Erlenmeyer flask or a gallon-sized carboy from a homebrew shop be sufficient?
Pull Times: The Tek mentions the following:
Is there any harm in letting the first couple pulls just sit for a couple of days or more then do the third and fourth pulls just sit for 2-3 weeks apart? Will that help or hinder the process? Alternately, is there any disadvantage to letting each pull just set for several days or more to increase the extraction percentage?
Finally, for using Acacia Confusa, I think I found the appropriate mods in this thread:
forum.dmt-nexus.me
Just wondering if there are any other updated tips for Q21Q21 a/o D-Limonene than is in that thread. Also, I read Q21Q21 had issues with shredded MHRB vs. powdered:
forum.dmt-nexus.me
If I'm using finely chipped (very thin) Acacia Confusa root bark, will that be alright for the above tek, or should I turn it to powder prior?
I'm planning on using the Q21Q21 Tek 1 with D-Limonene. I have powdered MHRB and chipped (very thin) Acaria Confusa root bark. I have two specific questions. Namely:
Volume. The tek calls for 30g-250g powdered MHRB, with 30g recommended for newbies. I'll start small (thinking 30g-50g), however if doing a larger batch (125g to 250g), what size vessels do you need for the volume? Would getting one 1000ml Erlenmeyer flask or a gallon-sized carboy from a homebrew shop be sufficient?
Pull Times: The Tek mentions the following:
The first pull if done immediately after getting the lime-bark to one of the consistencies should yield anywhere from 10%-35% (in my experience.) If the first pull is done after 6-8 hours however it will likely yield 25%-60%.
2 pulls done around 24 hours and 48 hours (or later) should be enough to get 80%-90% of the DMT (In my experience).
Pulls after that tend to be rather small but I highly recommends doing pulls at 1 week and another at 2 or 3 weeks to get all the DMT possible.
Is there any harm in letting the first couple pulls just sit for a couple of days or more then do the third and fourth pulls just sit for 2-3 weeks apart? Will that help or hinder the process? Alternately, is there any disadvantage to letting each pull just set for several days or more to increase the extraction percentage?
Finally, for using Acacia Confusa, I think I found the appropriate mods in this thread:
Acacia A/B extraction questions with Q21Q21, and BLAB tek + Salting with FASI
Hello, hello, hello! Hope i've posted this in the right place, my apologies if I haven't, I've no access to post in the grown ups section yet haha… anyway, I've been a lurker here at the nexus for quite sometime now, and found it extremely helpful and informative. There are some truly...
Just wondering if there are any other updated tips for Q21Q21 a/o D-Limonene than is in that thread. Also, I read Q21Q21 had issues with shredded MHRB vs. powdered:
Q21Q21 tek (and other limeteks) NOT recommended for shredded bark!
So being unable to get any powdered MHRB, I ended up with 500g of shredded bark which I hadn't used for extractions before. I figured before doing a large extraction I should do some tests and I did took two 30g samples of the bark to extract side-by-side. I chose Q21Q21 limetek with lime and...
If I'm using finely chipped (very thin) Acacia Confusa root bark, will that be alright for the above tek, or should I turn it to powder prior?