BioBoostedSpirit
ओं मणिपद्मे हूं
Greetings everybody !!!
I finally made some pics and want to share with you all how to make super cheap , easy to make and use ,small and portable ,glass hitter for dmt/changa.
All you need is an Glass pipette (the longer the better,but small pipettes also do just fine) approx 10cm , and used spring lighter. All you need from that lighter is a spring, small BIC lighter's spring is perfect, if the lighter is larger(big BIC) the spring will fit harder in the pipette.. A small saw(to carefully cut the pipettes tip,some pipettes doesnt need cutting coz the hole (for inhaling) is large already. Some hard sandpaper (to smooth the glass edges, just in case) , and maybe a needle ( as you see in the pics ,to carefully open a bigger hole in a pipette) , but once again if the pipette is good at inhaling you may not need that..
Everything is very simple : take the pipette , carefully cut it ,to make an inhaling hole bigger use a needle (just stick the needle in the hole and CAREFULLY turn it in one way, i small piece of glass should come off ) ,then CAREFULLY use sandpaper to smooth the edges and stick the knotted spring in opposite opening. Thats it !!!
So,the beauty of this method is coz the hitter is very small and you can take it almost everywhere (nature) whithout being scared of carrying a big , expensive device.You can throw it away anytime. Its from glass and easy to use. I must say its perfect for changa and enhanced leaf (just load your preferable amount, and smoke it in one big or couple of small hits, all you need is just light it up, no more flame needed. Same as with bong.
Now if you want to vape DMT freebase from it , here is the trick ..Before adding the DMT in it you should load the hitter with small amount of herb (i used white sage) creating a small bed, and then load your preferable amount of DMT.((( Also you can try and put some steel wool on top of the spring and vape spice without adding the herbs , but this one is on you , because i have not tried it ))) When your hitter is ready with DMT freebase on top of a small herb bed and you are ready to smoke , light up your lighter (torch lighter or normal lighter, mind that torch lighter produces bigger heat vapor) bring it close to the hole (its kinda vaping move , all you need is hot air flowing ) and inhale until all DMT is melted into a herb bed. Hold it as much as you can, exhale and right after >light up< (same as changa) the remaining herb bed (coz most of the freebase is melted into it) and make a final hit . Voila !!! :d
Idk if it sounds complicated, but i assure you ,my brother and i did the trick with the first try.:thumb_up:
In case of questions , feel free to ask me anything you want!
And here are the pics , enjoy buds
I finally made some pics and want to share with you all how to make super cheap , easy to make and use ,small and portable ,glass hitter for dmt/changa.
All you need is an Glass pipette (the longer the better,but small pipettes also do just fine) approx 10cm , and used spring lighter. All you need from that lighter is a spring, small BIC lighter's spring is perfect, if the lighter is larger(big BIC) the spring will fit harder in the pipette.. A small saw(to carefully cut the pipettes tip,some pipettes doesnt need cutting coz the hole (for inhaling) is large already. Some hard sandpaper (to smooth the glass edges, just in case) , and maybe a needle ( as you see in the pics ,to carefully open a bigger hole in a pipette) , but once again if the pipette is good at inhaling you may not need that..
Everything is very simple : take the pipette , carefully cut it ,to make an inhaling hole bigger use a needle (just stick the needle in the hole and CAREFULLY turn it in one way, i small piece of glass should come off ) ,then CAREFULLY use sandpaper to smooth the edges and stick the knotted spring in opposite opening. Thats it !!!
So,the beauty of this method is coz the hitter is very small and you can take it almost everywhere (nature) whithout being scared of carrying a big , expensive device.You can throw it away anytime. Its from glass and easy to use. I must say its perfect for changa and enhanced leaf (just load your preferable amount, and smoke it in one big or couple of small hits, all you need is just light it up, no more flame needed. Same as with bong.
Now if you want to vape DMT freebase from it , here is the trick ..Before adding the DMT in it you should load the hitter with small amount of herb (i used white sage) creating a small bed, and then load your preferable amount of DMT.((( Also you can try and put some steel wool on top of the spring and vape spice without adding the herbs , but this one is on you , because i have not tried it
))) When your hitter is ready with DMT freebase on top of a small herb bed and you are ready to smoke , light up your lighter (torch lighter or normal lighter, mind that torch lighter produces bigger heat vapor) bring it close to the hole (its kinda vaping move , all you need is hot air flowing ) and inhale until all DMT is melted into a herb bed. Hold it as much as you can, exhale and right after >light up< (same as changa) the remaining herb bed (coz most of the freebase is melted into it) and make a final hit . Voila !!! :dIdk if it sounds complicated, but i assure you ,my brother and i did the trick with the first try.:thumb_up:
In case of questions , feel free to ask me anything you want!
And here are the pics , enjoy buds
