Members of the previous forum can retrieve their temporary password here, (login and check your PM).

Reply to thread

Message

The mod is supposed to compensante and turn the wattage up if the mesh/coil gets cooled down, so the mesh should be heated to fx 220 deg. C continously, not dependent on how hard you inhale as in wattage mode.

The optimal combination of temp setting and max wattage is some what difficult to define, as different mods tend to behavee different in TC mode, but at
0,25-0,3ohm I would say watt 200-220 and max 23-30w. I have no idea if it is actually 220 deg C on the coil itself, but I have found the settings that works for me, following my thumb rule:

As a thumb rule I adjust the mod's temp settings( C and or TCR ) until the mesh glows a little bit when holding the fire button.
The faint glow should pulse on and off if the TC works properly. That is the optimal srtting in my opinion.

Your setup looks perfect, that should do it. All you have to do is find the optimal temp settings before loading. :thumb_up:

I just build my dripper with the new SS316 200 mesh 1.2 ohm/ft from vandyvape, the build is around 0,25 ohm.
I tested with my Vaporesso luxe mod on max 30w, 210 degrees C, and it worked perfectly, I'll test the new setup tonight or tomorrow.

<blockquote data-quote="Propello" data-source="post: 3848278" data-attributes="member: 43896">The mod is supposed to compensante and turn the wattage up if the mesh/coil gets cooled down, so the mesh should be heated to fx 220 deg. C continously, not dependent on how hard you inhale as in wattage mode. The optimal combination of temp setting and max wattage is some what difficult to define, as different mods tend to behavee different in TC mode, but at 0,25-0,3ohm I would say watt 200-220 and max 23-30w. I have no idea if it is actually 220 deg C on the coil itself, but I have found the settings that works for me, following my thumb rule:As a thumb rule I adjust the mod&#039;s temp settings( C and or TCR ) until the mesh glows a little bit when holding the fire button. The faint glow should pulse on and off if the TC works properly. That is the optimal srtting in my opinion.Your setup looks perfect, that should do it. All you have to do is find the optimal temp settings before loading. :thumb_up: I just build my dripper with the new SS316 200 mesh 1.2 ohm/ft from vandyvape, the build is around 0,25 ohm.I tested with my Vaporesso luxe mod on max 30w, 210 degrees C, and it worked perfectly, I&#039;ll test the new setup tonight or tomorrow.</blockquote>

[QUOTE="Propello, post: 3848278, member: 43896"] The mod is supposed to compensante and turn the wattage up if the mesh/coil gets cooled down, so the mesh should be heated to fx 220 deg. C continously, not dependent on how hard you inhale as in wattage mode. The optimal combination of temp setting and max wattage is some what difficult to define, as different mods tend to behavee different in TC mode, but at 0,25-0,3ohm I would say watt 200-220 and max 23-30w. I have no idea if it is actually 220 deg C on the coil itself, but I have found the settings that works for me, following my thumb rule: As a thumb rule I adjust the mod's temp settings( C and or TCR ) until the mesh glows a little bit when holding the fire button. The faint glow should pulse on and off if the TC works properly. That is the optimal srtting in my opinion. Your setup looks perfect, that should do it. All you have to do is find the optimal temp settings before loading. :thumb_up: I just build my dripper with the new SS316 200 mesh 1.2 ohm/ft from vandyvape, the build is around 0,25 ohm. I tested with my Vaporesso luxe mod on max 30w, 210 degrees C, and it worked perfectly, I'll test the new setup tonight or tomorrow. [/QUOTE]