Vaporizing

[meatman]

Well, I finally had a couple good pulls from some bark. So since I don't have much money I made a lightbulb vap. I have a scale that reads to .1g and tried to combine all my pulls to see how much I had. Didn't even register on my scale. I am not sure how accurate my scale is any longer since it's been forever since it has been calibrated. So I divided what I had into 2 piles and loaded the bulb.

First problem: apparently I didn't completely dry the bulb after cleaning it out. I saw a few very small drips making their way toward the crystals, after I loaded it of course. they eventually saturated a small bit of dose. I know the crystals aren't supposed to get wet, but why? what affect would it have had on trying to vap it?

Second problem: bulb cracked. continued vaporizing anyway.

The effects I experienced were very weak. Things seemed a little weird but that's as far as it went. My first few pulls yielded a pile about as big as a penny, maybe about an 1/8 of an inch high. My guess is I should have used all of my pulls, but I don't know. I'm working on my 3rd pull right now.

Any input is appreciated!

 

[Nanaki]

SWIM hears that even eating a lot of chocolate can potentiate the effects.
Or like 3 tablespoons of hershey's syrup in a cup of milk. It's the theobromine that does that.

SWIM has done THH and it worked very well with DMT, but it's slightly expensive.

 

[kagenical]

I've had *no* luck vaping DMT... Tried over 15 times without a breakthrough.

I just double up some screens in my pipe, hold a BIC lighter about half an inch above the pile of DMT, and breathe in slowly. Broke through first try.

 

[Nanaki]

I recommend a VaporGenie. Seriously, SWIM broke through hardcore on 15mg. He can normally just barely break through on this, but the VG seriously is a must have.

 

[meatman]

I'd love to get a vaporgenie but I used a lightbulb for a reason. i'm a broke-ass. maybe I'll try the machine next.

 

[endlessness]

I've had *no* luck vaping DMT... Tried over 15 times without a breakthrough.

I just double up some screens in my pipe, hold a BIC lighter about half an inch above the pile of DMT, and breathe in slowly. Broke through first try.

dont just double up some screens.. before spice vaporizes, it will melt and some might go through the screens.. Thats why one should use thick layer of ashes on the bottom, maybe even with a tiny bit of some herb at the very bottom.. that way even if it melt it will stay there

also dont expose the dmt directly to the flame.. put a layer of ashes on top too, can be quite a bit of ashes.. it really helps a lot

 

[acolon_5]

I'd love to get a vaporgenie but I used a lightbulb for a reason. i'm a broke-ass. maybe I'll try the machine next.

Even a makeshift "weed" pipe works better than a lighbulb vape in my opinion. I've never had good results with the lightbulb.

Bed of leaf is the way to go if a vaporizer is not accessable. Alternatively one can make "the machine" for only the cost of a mini alcohol bottle, charboy, and a drill. Copper tubing, a pinch of sand, and some oil, you might be done in 15 minutes or so.

 

[monkeyboy]

acolon, could swiy please explain the use of copper tubing, sand and oil- swim would like to make a machine, but forsee's problems getting a hole drilled in the bottom of the bottle.

 

[acolon_5]

It's a trick I learned from my friend.

He gets a piece of small diameter copper tubing (the size of the hole you want in the bottom of the bottle) and uses it like a drill bit. Cut an inch or two long piece. He puts it in a vice (with rubber to keep the bottle from shattering) adds a few drops of oil to the bottom of the bottle (where he will be drilling) and adds some sand to help grind the glass. Keep adding small pinches of sand and drops of oil as needed. He uses a bouncing motion with the drill (pressure, off, pressure, off) and in about 10-20 minutes he has drilled a hole through the glass.

I didn't think it would work the first time he showed me, but in an hour he had drilled 4 bottles using nothing but the above materials.