The VaporGenie
The VG is a vaporizing pipe which can be used for any kind of herb, changa and dmt.
The two most used versions are the Glass VaporGenie and the Classic VaporGenie. For comparison between them, read here: VG vs GVG
Datasheet:
Material: Pipe (GVG: glass, VG: wood) / ceramic (flame filter) / stainless steel (screens)
Seller: www.vaporgenie.com
Price: GVG: 119$ (only sold in official website) VG: 55$
Main advantages over other smoking methods: smooth vapor, effective vaporization.
You are adviced to buy an additional QUALITY torch lighter, ideally with bent shape. Here's an example of such good torch lighter. If not possible, a normal lighter will work very well too.
How to vaporize DMT with it:
Begin with the flame a few cms above the top and adjust as you go. With empty lungs, start inhaling slowly and steady. The idea is to inhale a dense vapour, but not too dense so that you start coughing. Its better to begin the inhaling with a not so dense smoke, and then make it denser towards the end. Keep the vapor in the lungs for as long as possible, at least 10 seconds. If you coughed or exhaled before this or couldnt inhale with all the lungs, try keeping the flame further away or adjusting the speed of inhaling so that its a bit less dense. You can also exhale a bit of the air/vapor out and inhale fresh air again, to maximize how much you keep in the lungs instead of exhaling it all out. If you get the technique right, 1-3 inhales should be enough for a sure breakthrough
Modification needed for pure dmt crystals:
In order to prevent the spice from melting into your VG, you want to apply one of the following solutions:
1: Use a ceramic pad where the screen should be, and put the DMT on top of that
2: get a volcano liquid pad, which is a cheap inert stainless steel pad made specifically for vaporization, and cut it up to fit the vaporgeniePutting a bed of herbs below the dmt or enhancing some herbs with your dmt by pre-dissolving it in herbs before vaporizing.
3: Put a bed of herbs on top of the screen so that the DMT melts into them instead of through the screen and into the pipe
Cleaning the VG:
VG:
The vaporgenie can be cleaned with hot water and a pipe cleaner (as sold in the official website). Do not use alcohol, as it may damage the wood finish. For more info also check the VaporGenie FAQ in their official website
GVG:
One can soak/shake/wash it with IPA, Acetone or Alcohol. If desired, this can be evaporated onto some herbs for infusing them with the active oil (which is mostly DMT and maybe partly DMT N-oxide which is safe and psychoactive), or otherwise just throw the solvent away. A pipe cleaner can help getting rid of resin that refuses to be removed, but a longer soak should take care of virtually all resin
One can also use vinegar to dissolve any DMT/oil condensating in the pipe, and then put the vinegar back into an ongoing DMT extraction to re-extract it.
Any further discussion or questions can be made in this thread. Thanks to Mr DMT for helping writing this overview.
The VG is a vaporizing pipe which can be used for any kind of herb, changa and dmt.
The two most used versions are the Glass VaporGenie and the Classic VaporGenie. For comparison between them, read here: VG vs GVG
Datasheet:
Material: Pipe (GVG: glass, VG: wood) / ceramic (flame filter) / stainless steel (screens)
Seller: www.vaporgenie.com
Price: GVG: 119$ (only sold in official website) VG: 55$
Main advantages over other smoking methods: smooth vapor, effective vaporization.
You are adviced to buy an additional QUALITY torch lighter, ideally with bent shape. Here's an example of such good torch lighter. If not possible, a normal lighter will work very well too.
How to vaporize DMT with it:
Begin with the flame a few cms above the top and adjust as you go. With empty lungs, start inhaling slowly and steady. The idea is to inhale a dense vapour, but not too dense so that you start coughing. Its better to begin the inhaling with a not so dense smoke, and then make it denser towards the end. Keep the vapor in the lungs for as long as possible, at least 10 seconds. If you coughed or exhaled before this or couldnt inhale with all the lungs, try keeping the flame further away or adjusting the speed of inhaling so that its a bit less dense. You can also exhale a bit of the air/vapor out and inhale fresh air again, to maximize how much you keep in the lungs instead of exhaling it all out. If you get the technique right, 1-3 inhales should be enough for a sure breakthrough
Modification needed for pure dmt crystals:
In order to prevent the spice from melting into your VG, you want to apply one of the following solutions:
1: Use a ceramic pad where the screen should be, and put the DMT on top of that
2: get a volcano liquid pad, which is a cheap inert stainless steel pad made specifically for vaporization, and cut it up to fit the vaporgeniePutting a bed of herbs below the dmt or enhancing some herbs with your dmt by pre-dissolving it in herbs before vaporizing.
3: Put a bed of herbs on top of the screen so that the DMT melts into them instead of through the screen and into the pipe
Cleaning the VG:
VG:
The vaporgenie can be cleaned with hot water and a pipe cleaner (as sold in the official website). Do not use alcohol, as it may damage the wood finish. For more info also check the VaporGenie FAQ in their official website
GVG:
One can soak/shake/wash it with IPA, Acetone or Alcohol. If desired, this can be evaporated onto some herbs for infusing them with the active oil (which is mostly DMT and maybe partly DMT N-oxide which is safe and psychoactive), or otherwise just throw the solvent away. A pipe cleaner can help getting rid of resin that refuses to be removed, but a longer soak should take care of virtually all resin
One can also use vinegar to dissolve any DMT/oil condensating in the pipe, and then put the vinegar back into an ongoing DMT extraction to re-extract it.
Any further discussion or questions can be made in this thread. Thanks to Mr DMT for helping writing this overview.