Psilocybecube1
Rising Star
- Merits
- 42
Hey guys how goes it!!?? SWIM is in love with this forum and can't wait to move up the chain! sooo anyway. SWIM is doing a STB Tek for the first time so SWIM is going to do an outline of the procedure and let me know if u have any pointers or suggestions for this SWIM just wanna make sure it is done right and cleanly!
So SWIM start with a pound of MHRB and two gallon milk jugs and SWIM fill each jug up halfway with water and use funnel to mix a pound of lye in each jug mixing about a 3rd of the lye at a time and keeping the jugs in a cold water bath while mixing because the dissolving lye will produce some heat.
Next SWIM mixes the MHRB with both jug a pound of bark in each, shake each one vigorously add a lil hot water to make it less sludgy and let sit in hot water bath for a hour to allow the lye to break down the bark and pull the DMT from the particals shaking periodically after the hour on to the next step
Now SWIM adds 400 mls of Naptha and shakes them and turns the jugs around being careful to not create an emulsion that will have to wait to let settle in a heat bath in the sink or bath. after it has settled (45min) SWIM pours the naptha off into a second jug until the MHRB layer is very close then the small leftover layer is poured into a seperation funnel and the basic layer is returned to the jug and the naptha is returned to its seperate jug
After 3 to 4 pulls with this method the washing jug is full of pulled naptha. Now SWIM is ready to do a polar wash! SWIM mixes sodium carbonate and water in a jar until it is dissolved to where it is cloudy clear (enough to get a pH of 9) then about an inch n half is poured into the seperation funnel for measurement and is then drained into the naptha and is shaken vigorously and it seperates is seconds on the bottom as a orange-red layer of water that is drained and is repeated a second time after that a non pH adjusted wash is done very quickly so as to collect any residual lye and keep from ionizing any DMT to the water.
The last part is done to dry the naptha and make sure there is no water floating in it by taking a small handful of Epsom salts on a plate and microwaved to bake any moisture out and then is broken up and dropped in the naptha jug and shaken around after it is settled the naptha is poured through a coffee filter in a 2 liter bottle funnel to filter all the salt out of the solvent. After that SWIM puts the jug in the freezer for 72 hours or more and pours the naptha through the funnel filter to collect any DMT crystals that are floating and then the naptha can be reused.
That is the Tek that SWIM is using this weekend to do this his first time any pointers or suggestions are completely encouraged to do so. Another question is where can SWIM aquire some gloves and glasses that will not melt when coming in contact with lye SAFTEY FIRST KIDS!! IF ANYTHING SWIM JUST NEEDs TO KNOW THE KIND OF PLASIC THAT WILL NOT MELT WHEN IN CONTACT WITH LYE thanx and SWIM hopes this place stays as friendly and supportive as SWIM has seen so far!
So SWIM start with a pound of MHRB and two gallon milk jugs and SWIM fill each jug up halfway with water and use funnel to mix a pound of lye in each jug mixing about a 3rd of the lye at a time and keeping the jugs in a cold water bath while mixing because the dissolving lye will produce some heat.
Next SWIM mixes the MHRB with both jug a pound of bark in each, shake each one vigorously add a lil hot water to make it less sludgy and let sit in hot water bath for a hour to allow the lye to break down the bark and pull the DMT from the particals shaking periodically after the hour on to the next step
Now SWIM adds 400 mls of Naptha and shakes them and turns the jugs around being careful to not create an emulsion that will have to wait to let settle in a heat bath in the sink or bath. after it has settled (45min) SWIM pours the naptha off into a second jug until the MHRB layer is very close then the small leftover layer is poured into a seperation funnel and the basic layer is returned to the jug and the naptha is returned to its seperate jug
After 3 to 4 pulls with this method the washing jug is full of pulled naptha. Now SWIM is ready to do a polar wash! SWIM mixes sodium carbonate and water in a jar until it is dissolved to where it is cloudy clear (enough to get a pH of 9) then about an inch n half is poured into the seperation funnel for measurement and is then drained into the naptha and is shaken vigorously and it seperates is seconds on the bottom as a orange-red layer of water that is drained and is repeated a second time after that a non pH adjusted wash is done very quickly so as to collect any residual lye and keep from ionizing any DMT to the water.
The last part is done to dry the naptha and make sure there is no water floating in it by taking a small handful of Epsom salts on a plate and microwaved to bake any moisture out and then is broken up and dropped in the naptha jug and shaken around after it is settled the naptha is poured through a coffee filter in a 2 liter bottle funnel to filter all the salt out of the solvent. After that SWIM puts the jug in the freezer for 72 hours or more and pours the naptha through the funnel filter to collect any DMT crystals that are floating and then the naptha can be reused.
That is the Tek that SWIM is using this weekend to do this his first time any pointers or suggestions are completely encouraged to do so. Another question is where can SWIM aquire some gloves and glasses that will not melt when coming in contact with lye SAFTEY FIRST KIDS!! IF ANYTHING SWIM JUST NEEDs TO KNOW THE KIND OF PLASIC THAT WILL NOT MELT WHEN IN CONTACT WITH LYE thanx and SWIM hopes this place stays as friendly and supportive as SWIM has seen so far!
