-
Members of the previous forum can retrieve their temporary password here, (login and check your PM).
yield whole bark vs pp
- Thread starter flyboy
- Start date
ismokecrystals
Rising Star
What's pp?
I only use the pre-powdered Mimosa anymore....after buying both the whole & "PP" bark from 3 different vendors to test it.
The only difference between them being the amount of work needed to get started on my extraction & the ease of filtering out the plant matter after the acid soak step.
When I've powdered the bark myself, I can never get it fully powderized with my blender, like they do. There is always a few stringy fibers left over, etc... Filtering the solids out is so much easier when it's all the same consistency.
I suppose if you are planing on purchasing a ton of it to store long term (like years), you may want to leave it as whole bark until you are about to use it. The DMT inside probably has a longer shelf life when it is protected from the elements by the cell structure of the whole bark.
Quality & yield was absolutely no different....& I tried bark from 3 different vendors to verify that.
Hope that helps!
WS
The only difference between them being the amount of work needed to get started on my extraction & the ease of filtering out the plant matter after the acid soak step.
When I've powdered the bark myself, I can never get it fully powderized with my blender, like they do. There is always a few stringy fibers left over, etc... Filtering the solids out is so much easier when it's all the same consistency.
I suppose if you are planing on purchasing a ton of it to store long term (like years), you may want to leave it as whole bark until you are about to use it. The DMT inside probably has a longer shelf life when it is protected from the elements by the cell structure of the whole bark.
Quality & yield was absolutely no different....& I tried bark from 3 different vendors to verify that.
Hope that helps!
WS
I kind of get what you mean, I rather enjoy the process of pounding out & breaking down B.Caapi vine into it's thin fibers by hand myself, when preparing Ayahuasca.flyboy said:
But powdering Mimosa bark is just a pain in my ass!
Using more liquids, better mixing & making sure that it stays warm throughout the process, should cure that right up.flyboy said:
Whether you started with whole or pre-powdered bark shouldn't make any difference here, as you are going to powder your whole bark for the extraction anyway.
TIP:
You want the bark solution to be a freely flowing liquid, not a mud or thick in any way.
If the entire solution is not a liquid pretty much the consistency of water, the DMT can not move as freely within the solution & your yield will more than likely suffer, as some of the DMT molecules stay trapped in the plant-matter-mud, instead of fully migrating into the acidic water.
When finished soaking, you need to filter the solids out of the liquid really well too, for that same reason.
I use a Buchner Funnel setup to vacuum filter the liquids out of the solution. It fully separates the liquids from the solids & I know for sure that I've got all the DMT out of the bark powder because it is returned to 98% dry once the filtering is finished!
I prefer to use an A/B tek (Vovin's tek), as I prefer very pure DMT over anything yellowish or jungle spice, the effects are so much clearer & focused.
I'll usually extract around 100-120g of MHRB when I do it & I'll do three acidic water soaks, using around 300-400ml of warm water for each, with a pH around 2.5-to-3.
So once the Acid soak step is all finished, I have around 900-1000ml of purple, acidic/DMT-water.
Which is filtered very well & then reduced down to around 300-500ml.
(in the oven at 130-150F degrees for around 4-6 hours...tedious, but worth it! check the pic! ...yes that's my DMT)
Before doing a defat & then basifying, pulling with Naptha & freeze precipitating.
Hope I didn't go on too long there...
Cheers!
WS
Attachments
ismokecrystals
Rising Star
I know Pedro sifts his bark after grinding.
I've only ever used powdered, no problems at all.
I've only ever used powdered, no problems at all.
Shredded is THE best if you can find it. As it lets you see what you got (vendors couldn't really adulterate it.) It's also much easier to work with than pre powdered bark. This is because the powder literally turns to goop, and regardless of the tek , is next to impossible to strain On the other hand the shredded strains with ease and yeilds are the same.
Two great reasons why shredded , under most circumstances is the way to go. Peace and Godspeed!
Two great reasons why shredded , under most circumstances is the way to go. Peace and Godspeed!
Either whole, shredded, or powdered will work well for limtek.
But SWIM would definitely trust the quality and purity of whole more than powdered. Most find powdered yields just fine, though.
But SWIM would definitely trust the quality and purity of whole more than powdered. Most find powdered yields just fine, though.
Spiceman said:
Check out a Buchner Funnel filtering setup!!
It is a vacuum based filtering setup & works great for a number of things!
Not too expensive either.
WS
hmmmmmm, interesting name, interesting avatar...mombreast!?! indeed...shoe said:
SnozzleBerry said:
The avatar of mombreast has been removed now.
Kind regards,
The Traveler
mombreast said:I am very sorry Traveler
It's alright, I'm glad you'r not making a fuzz about it.
Kind regards,
The Traveler
