• Members of the previous forum can retrieve their temporary password here, (login and check your PM).

I'm a beginner, any advice is much appreciated

DeeEmTee28

No heart, no peace. Know heart, know peace
Joined
Nov 17, 2026
Messages
4
Merits
122
Hiya guys. I've recently been extracting my own DMT using MHRB, distilled water, NaOH for extraction use some rock salt to help with any emulsions and Zippo lighter fluid for precipitation, which has been working ok. I've had 4 pulls now and seem to get an ok(ish) amount of white DMT crystals. I found a guide online and followed the process to a tee, and the results have took me places my human bran can't fathom haha, it's beautiful place, it's beautiful stuff. [[mod edit: no sourcing]] Do you have any other tips for a bigger yield.

For context I usually measure:
150G MHRB
500ML of distilled water
80-100G NaOH
20-30G of rock salt
200ml of zippo lighter fluid.

Once I mix the NaOH with water, I'll let it cool to room temperature before adding to finely shredded MHRB. I'll let that sit for 40/60 mins and shake in between to mix throughly. Then I'll add the zippo lighter fluid, at this point I like to emulsify the mixture and wait 30/40 mins before it's clear again and extract with a pipette in a seperate glass suitable to freeze. Then repeat until the lighter fluid is gone. Then I'll precip In the freezer for 18/24 hours.

Any advice on what I'm doing would be greatly appreciated
 
Last edited:
Welcome. Sounds like you have your foot firmly in the DMT door.

Please delete any talk of where you buy your MHRB etc from. I'm sure a Mod will be along shortly to do it for you anyway.
 
Hi from the UK too.
You may be able to get a little more from your powdered Root Bark by wetting and Freeze/Thawing a few times as it helps break the cell walls to help get the good stuff out.
Unless you are time-constrained you can leave your Powder and Caustic mix longer which may also help get a bit more yield.
3x Naphtha pulls is usually enough, the 4th doesn't usually give me much back but you may get a little Goo which is still good stuff once fully evapourated, you can either add all these together or Freeze precip in different dishes.
 
Why are you using sodium superoxide as your base? It has zero benefits over sodium hydroxide, and only downsides. When you put it into water, it decomposes into sodium hydroxide anyway, but it also produces oxygen gas and hydrogen peroxide, neither of which are useful in the reaction you want, and could both produce secondary reactions that you dont know or understand. Mixing it with water is also a much more violent reaction than just pure sodium hydroxide powder, so youre way more at risk of being splashed with boiling sodium hydroxide solution. Producing excess oxygen gas around a volatile, highly flammable liquid like petroleum ether is also a recipe for disaster. Additionally, petroleum ether is normally a mixture of pentane and hexane. Hexane is a chronic neurotoxin that can cause severe, irreparable damage to your central nervous system so every single time you breathe its vapour, and every single time you get some of it on your skin, you are causing yourself real, long term health damage.

Do yourself a favour - start using pure chemicals so you know what reactions are actually taking place in your solution, and stop using things that are known to be highly toxic. I would worry about that before I worry about yield. Pure sodium or potassium hydroxide are both better than sodium superoxide. They are both more basic, so you have to use less of them to attain the required PH, and they both react less violently with water. Heptane is better than petroleum ether or naphtha. Its flashpoint is higher than both, and its toxicity is less than both, but its vapour pressure is still high enough that it very readily and quite quickly evaporates even at atmospheric pressure and room temperature.
 
Why are you using sodium superoxide as your base? It has zero benefits over sodium hydroxide, and only downsides. When you put it into water, it decomposes into sodium hydroxide anyway, but it also produces oxygen gas and hydrogen peroxide, neither of which are useful in the reaction you want, and could both produce secondary reactions that you dont know or understand. Mixing it with water is also a much more violent reaction than just pure sodium hydroxide powder, so youre way more at risk of being splashed with boiling sodium hydroxide solution. Producing excess oxygen gas around a volatile, highly flammable liquid like petroleum ether is also a recipe for disaster. Additionally, petroleum ether is normally a mixture of pentane and hexane. Hexane is a chronic neurotoxin that can cause severe, irreparable damage to your central nervous system so every single time you breathe its vapour, and every single time you get some of it on your skin, you are causing yourself real, long term health damage.

Do yourself a favour - start using pure chemicals so you know what reactions are actually taking place in your solution, and stop using things that are known to be highly toxic. I would worry about that before I worry about yield. Pure sodium or potassium hydroxide are both better than sodium superoxide. They are both more basic, so you have to use less of them to attain the required PH, and they both react less violently with water. Heptane is better than petroleum ether or naphtha. Its flashpoint is higher than both, and its toxicity is less than both, but its vapour pressure is still high enough that it very readily and quite quickly evaporates even at atmospheric pressure and room temperature.
Thanks for your reply man, and ofcourse your concerns. I completely got it wrong, I had to check back at what you was implying. I use NaOH as my Base not NaO2. (Editied original post)
 

Attachments

  • Screenshot_20261117_184201_Samsung Browser.jpg
    Screenshot_20261117_184201_Samsung Browser.jpg
    246.4 KB · Views: 4
Back
Top Bottom