My Machine

[Aoutiv]

I used a single serving Absolut vodka bottle, a dremel with two diamond drill bits (one for hole, other for design), and Scotch Brite Stainless Steel scrubbing pad (this the right kind?). It took about 35 minutes (60 minutes if you include purchasing the materials).

I decided to get a little carried away with the precision diamond drill bit and here is what I came up with. In case you can't tell whats on it--on one side it says "The Machine", on the other side is the dmt molecule, on the bottom is a pie design, and on the cap is the ohm symbol. Enjoy.

 

[ancientpledge]

Very nice! I especially like the molecule. You did a great job on the entire piece, it's gonna be sweet to have around

 

[DMTripper]

Good work
And how does it work for you?

 

[sameoldsongam]

that's awesome.

 

[Madcap]

Very very cool! Nice touches

 

[69ron]

Aoutiv, I never thought of using a Dremel for that purpose. I have those diamond bits sitting around. How easy was it to make that hole? How long did that part take?

 

[antrocles]

very nice artistic flair my friend....you are like the picasso of dremelfication!

thanks for sharing your creative fruits!

LOVE AND GRATITUDE!!

 

[obliguhl]

I like it!

(don't forget to burn the coating off of the brillo before using your new machine.

 

[Aoutiv]

DMTripper: I have not used it yet, was oh pharmahuasca tonight (so intense, twas like mushroomsx100).

69ron: I had two different diamond bits in the set, a ball and a longer type one. The hole was not easy to make, but not too difficult. I made an intial tiny hole, then just swirled it around (if that makes sense). I ruined one of the bits because I let it get to hot and it like, melted the diamond part away (dont ask me how). It probably took 20 minutes, but was all I had to work with. A drill with diamond bit would be MUCH quicker.

obliguhl: Ya, I took the steel back out, flamed it with torch lighter. It turned darker then as I was putting it in flakes started to fall off. I did not want to inhale these flakes so I ran it under hot water which seemed to do the trick.

Everyone else: Thanks for the compliments. I tend to get carried away with such things. I'm glad other people can enjoy it (even though it's just pictures :/). I shall test it tomorrow sometime and report back on how well it worked. Once again, thanks for the feedback!

Peace

 

[Espiridion]

.
.
If anyone wants to cut a hole in glass quickly, then go to the hardware store and buy a glass and tile bit. It is flat and tapered from tip to back with a bit of a curve. They work GREAT!!! And take about twenty seconds. Three, four backs tops.


Nice machine!!! Love the molecule and the OM.

I'll take two!!



J
.
.

 

[corridors of my cells]

hahahaha ... very cool machine ... im jealous we exchange the machines?

 

[Kisper]

I love the molecule. Nice work overall.

 

[Ayawasqero]

Nice.

 

[Jurema]

I wanna know how this worked for you so I can make one. Doesn't the mouth piece get warm?

 

[Phlux-]

very nice.

 

[smokeydaze]

Great job.

 

[camakazi]

lovely bit of work on that machine there. I thought about engraving my machine with design, but Im afraid my skills with a pencil are bad enough without adding a powertool to the equasion.

 

[darkstate]

Love it :d

 

[Ayawasqero]

I wanna know how this worked for you so I can make one. Doesn't the mouth piece get warm?

Why don´t You just buy Yourself a small glass (intended for smoking the MJ) pipe? I bet at Your local ethno shop they have a plenty of them.

 

[bonestoner]

Ω i thought this was the ohm symbol...how i was taught in electronic engineering anyways.