First time extracting (DMT Quiktek) need some help

[debutemushroom23]

I'm posting this for a friend as usual, he isn't quite internet savy.

He stumbled upon this tek http://www.dmt-nexus.me/phpBB2/viewtopic.php?t=70 and to him it seems a good idea. So far he has gathered he only need 2 or 3 things from the store plus the mimosa. Lye, Naphtha, Mimosa, and a large pan.

My friend plans on doing this and he is a beginner. Any tips would be appriciated by him and anyone who kows someone with experience on this method would also be appriciated.

Is there anything he should know before hand? Also, what is naphtha? I know where to find Lye, but he's heard not to use Zippo lighter fluid, so what should he use as naphtha?

 

[Infundibulum]

Hey, I presume you also live in a country where Naphtha is unheard of....

Basically it is a petroleum distillate which contains light aliphatic hydrocarbons id est 5-10 carbons. Hexane, often highly recommended is a six carbon alkane.

Go ahead and use zippo lighter fluid, as it has been used with great success. Go for the cheapest brand, like Ronsonol, check

http://outdoor-living.hardwarestore.com/58-233-charcoal-and-lighters/ronsonol-lighter-fuel-226357.aspx

and make sure you freeze-precipitate and then reuse your fluid so you won't need loads of it.

and please do not try to use White Spirit or Turpentine Substitute. A friend has repeatedly told me that these won't work whatsoever!

 

[shoe]

SWIM got good results with white spirit (which IS turpentine substitute) until recently, however SWIM suspects this is to do with old stock converting to dmt n-oxide which just plain won't evaporate. symptoms: slow evaporation to begin with, and then none at all. also, won't freeze percipitate because its not concentrated enough. any that you do manage to get to evaporate leaves fuck all in the way of crystals and only a slight layer of dmt smelling grease. (due to the fact that you only evaporated a tiny amount.)

SWIM will switch to lighter fluid.

 

[debutemushroom23]

Friend did a first pull with this tek:

Final Write-Up

--------------------------------------------------------------------------------

Required Items
Agents
- Any amount of MHRB (preferrably 100+g)
- Roebic Drain Cleaner (Basic Lye)
- VM&P Naptha (Non-Polar Solvent)
- Distilled Water
Tools
- Turkey Baster
- Stainless Steel Utensil
- Glass Pie Dish
- Quart Jars with Lids
Note: You will need one quart jar for each cup of MHRB powder (100g of MHRB is about 1 cup powder).

Step 1 Prepare Bark:
1) Break and twist up the MHRB by hand into as small pieces as possible,
no need to hurt your hands. Use plyers if the bark is tough.
2) Put a handful of the broken up MHRB into the blender to turn it to
powder.
3) Empty the powder from the blender into a bowl or large measuring cup
and repeat blending until all of the powder is ready.

Step 2 Mix Jars:
4) First, add two cups of distilled water to each empty quart jar.
Note: Put on goggles and rubber gloves for this part...
5) Add three tablespoons of Lye to each jar.
6) Stir the liquid gently with the stainless steel utensil.
7) Slowly and gently add 1 cup of MHRB powder to each jar.
Be careful not to splatter or spill.
8) Stir the powder gently until it is absorbed evenly and it turns black.
9) Add 150ml-300ml of Naptha , just leave enough room to shake contents.
10) Wipe the tops of the jars and put the lids on, then shake vigorously.

Let the jars sit overnight (8-12 hours should do probably), shake every now and then....

Step 4 Syphen Naptha
1) Syphen the Naptha off the top using the Turkey Baster and squirt it into the glass Pie Dish, being extremely careful to get only the clear Naptha and no black gunk (lye).
2) Add more Naptha to the jar and repeat this step a total of 3x.

Step 5 Evaporate Naptha
Put a fan next to, or a Dehydrator over the pie dish filled with Naptha . When it is dried out there will be white crystals everywhere. Continue to dry until no Naptha is smelled.

NOTE: By making the soaks only 12 hours long (maybe less, like 8?) and using thick layers of Naptha to obtain easy and pure pulls, the resulting crystals should be very clean and further processing unecessary. Also this tek is for low quantities so keep in mind additional washes could decrease the yield to unacceptable levels. My friend says 100g MHRB produced 20 mind blowing experiences without any harshness.

Either his naptha has not evaporated totally, or he really messed up. He left the naptha in a glass pie pan in the shed all day, but turned the fan off thinking it was not a good idea to leave an appliance running while he was not there. Turns out the day ended up being really humid, "Doh!"

So the glass pan of naptha almost looks like condensation he says, maybe it just needs more time to evap or the heat really screwed his first pull up.