Okay guys, this is what I have come up with after a short while extracting DMT. Take it as you will but the results are undeniable and very fast.
First off, get a 3L ultrasonic cleaner, from vevor or harbor freight or wherever really. I personally take the bottom plate off and add some rtv (silicone gasket maker) to the panel because it quites the noise very well. This is the crucial part here for the high yield. Will go into further detail soon.
Go with the standard ratio for STB extraction, with lye and distilled water. Honestly I didn't even measure the amount of water I just filled the ultrasonic cleaner up after adding my previous batch of STB leftovers to the cleaner and 100 more mg of Root Bark. For a total of 200 mg of Root bark, partially extracted from first few pulls. Whatever, anyways
Turn the ultrasonic cleaners heater setting all the way up, mine goes to 80 degrees Celsius, and turn the timer on and get that thing running. Usually they go in 30 min cycles. The ultrasonic frequencies create bubbles inside the cell walls of the plant material basically, allowing full penetration of the material and full extraction of the DMT. I only let mine run one cycle before starting to add naptha.
After one or two full 30 min cycles in the cleaner, basically every bit of the powdered root bark is completely dissolved,more or less, in the water. Like super quickly and super thoroughly, I was shocked tbh. Again, I didn't measure I just poured a good bit of naptha in.
Run another full cycle with heat on, and during which I used a coffee frother to stir and mix up the naptha into the root bark lye water soup. After that 30 minute cycle ran fully I used a "flavor injector" or a big cooking syringe with a metal tip (5$ at any super market) to remove the naptha layer on top. Yes 30 min might be long, but we're going to purify it anyways.
Do as many pulls if this as you wsnt to, I choose to go until no more yellow is showing up in the naptha. Takes quite a few pulls because the cleaner really opens up those cell layers. Seriously this shit is high yeild like no other.
Do the normal freeze precip, pour off the naptha and save it to do a full evap on later.
Take your nice white DMT powder and put it in a new jar. Add all of the precipitations together or run them separately. Either works. Go get a can of premium starting fluid, the kind that advertises 50% ether on it. The other 50% is heptane. And a trace of liquid petroleum gas whatever that may be. Running the bottom of the jar in hot water spray a small amount of starting fluid in the jar, just barely enough for it to dissolve everything. Really won't take much. Let it sit and don't touch for a couple hours maybe a day max, depends how impatient you are.
You will be left with some beautiful and tasty extremely pure DMT crystals, the kind that look almost like crystal meth mixed with thc diamonds. There will be some other goo left behind most likely, I just separate the diamonds with tweezers into a separate location once they're mostly evaporated of solvent. And then run that too and whatever's left through a few more recrystallization cycles until no more crystal DMT comes out.
It's super easy, not time consuming at all, and very high yeild. Try it, give me your feed back and criticism, and any suggestions to improve on this. I only came up with this today and wanted to share because the world deserves to know this info and surely someone else can build onto it from here.
Haven't gotten the numbers from my yeild yet, but will post back with the actual percentages of pure DMT crystals when I have it all finished.
First off, get a 3L ultrasonic cleaner, from vevor or harbor freight or wherever really. I personally take the bottom plate off and add some rtv (silicone gasket maker) to the panel because it quites the noise very well. This is the crucial part here for the high yield. Will go into further detail soon.
Go with the standard ratio for STB extraction, with lye and distilled water. Honestly I didn't even measure the amount of water I just filled the ultrasonic cleaner up after adding my previous batch of STB leftovers to the cleaner and 100 more mg of Root Bark. For a total of 200 mg of Root bark, partially extracted from first few pulls. Whatever, anyways
Turn the ultrasonic cleaners heater setting all the way up, mine goes to 80 degrees Celsius, and turn the timer on and get that thing running. Usually they go in 30 min cycles. The ultrasonic frequencies create bubbles inside the cell walls of the plant material basically, allowing full penetration of the material and full extraction of the DMT. I only let mine run one cycle before starting to add naptha.
After one or two full 30 min cycles in the cleaner, basically every bit of the powdered root bark is completely dissolved,more or less, in the water. Like super quickly and super thoroughly, I was shocked tbh. Again, I didn't measure I just poured a good bit of naptha in.
Run another full cycle with heat on, and during which I used a coffee frother to stir and mix up the naptha into the root bark lye water soup. After that 30 minute cycle ran fully I used a "flavor injector" or a big cooking syringe with a metal tip (5$ at any super market) to remove the naptha layer on top. Yes 30 min might be long, but we're going to purify it anyways.
Do as many pulls if this as you wsnt to, I choose to go until no more yellow is showing up in the naptha. Takes quite a few pulls because the cleaner really opens up those cell layers. Seriously this shit is high yeild like no other.
Do the normal freeze precip, pour off the naptha and save it to do a full evap on later.
Take your nice white DMT powder and put it in a new jar. Add all of the precipitations together or run them separately. Either works. Go get a can of premium starting fluid, the kind that advertises 50% ether on it. The other 50% is heptane. And a trace of liquid petroleum gas whatever that may be. Running the bottom of the jar in hot water spray a small amount of starting fluid in the jar, just barely enough for it to dissolve everything. Really won't take much. Let it sit and don't touch for a couple hours maybe a day max, depends how impatient you are.
You will be left with some beautiful and tasty extremely pure DMT crystals, the kind that look almost like crystal meth mixed with thc diamonds. There will be some other goo left behind most likely, I just separate the diamonds with tweezers into a separate location once they're mostly evaporated of solvent. And then run that too and whatever's left through a few more recrystallization cycles until no more crystal DMT comes out.
It's super easy, not time consuming at all, and very high yeild. Try it, give me your feed back and criticism, and any suggestions to improve on this. I only came up with this today and wanted to share because the world deserves to know this info and surely someone else can build onto it from here.
Haven't gotten the numbers from my yeild yet, but will post back with the actual percentages of pure DMT crystals when I have it all finished.
