• Members of the previous forum can retrieve their temporary password here, (login and check your PM).

Pure white DMT waxy with oily residue?

Snarr

Rising Star
Joined
Feb 15, 2024
Messages
13
Merits
42
If SWIM did their first extract using Nomans STB tek, and the final result of the first 2 pulls was a plate full of snowflake like crystals that are very soft and powdery, have a waxy texture and leave a oily residue on the fingers, would this be normal?

Also, if the aforementioned SWIM misinterepted some steps in the Nomans tek that Entropymancer addended, namely the sodium carbonate wash (and when to do it), would it be acceptable to perform a re-crystalization to perform said wash?
 
they there,

the waxiness could be DMT-oxide, which you'd expect in your e.g. MHRB. [espc if it's older]
It can be formed in the drying process if there is too much air circulating in your evap chamber.

You can do a Zinc powder reduction of the oxide, [get off ebay if you are in the states] and a few other chemical reagent companies which will increase your overall yield of DMT [DMT oxide is not soluble in Naptha, so you won't get much through]
Alternately ascorbic acid will apparently work [ref 69Ron],
I haven't tried this but plan to in the near future [and will compare vs a zinc powder extraction for efficiency].

DMT oxide has a slightly different effect people I've talked to have found,
less strong, gentler and perhaps 'warmer' in effect?

hope that helps some.
 
Is this a common occurrence? SWIM says the room is not overly breezy and SWIM followed the tek to the letter. Would any other factors come into play, like the age of the Lye, which was old but looked in tact.
 
nah old lye should not matter at all.

how did SWIY get the crystals in the final step, freeze precip or evap? Evap (specially with a lot of air/fan near) can increase creation of n-oxide because of all the oxigen the dmt is being exposed to. In any case, N-oxide is psychoactive also so it wouldnt be a problem except for the looks.

Another possibility is that there is still a little bit of solvent trapped in between the crystals. Break them up and let them open to the air on top of a filter or something for a while, see if it dries more.

Is your solvent good?? Did you evap it alone before to see if it leaves residues? thats another possibility, impurities from the solvent.
 
One other possibility is that the DMT is simply melting on your fingers as you pick them up. Body temp is definitely high enough to melt DMT, and even pure white crystaline dmt freebase will turn a little yellow when it melts.
 
DMT, even when freeze precipitated, can often be a bit waxy, especially when the bit of residual solvent is left to evaporate from the crystals. The polar wash, usually done before evapping or freeze precipitating can help clean this up, but recrystallization can make it clean, as well as help remove the waxiness left from the first precipitation. The white/clearer crystals usually have much less smell, and are not sticky to the touch, however, if held in the hands or warmed, it can turn sticky as it melts.
 
DMT, even when freeze precipitated, can often be a bit waxy, especially when the bit of residual solvent is left to evaporate from the crystals. The polar wash, usually done before evapping or freeze precipitating can help clean this up, but recrystallization can make it clean, as well as help remove the waxiness left from the first precipitation. The white/clearer crystals usually have much less smell, and are not sticky to the touch, however, if held in the hands or warmed, it can turn sticky as it melts.

This makes sense considering the first pull was not washed and was oily, where the second pull which was washed had sharper crystals seemed more defined.

One other possibility is that the DMT is simply melting on your fingers as you pick them up. Body temp is definitely high enough to melt DMT, and even pure white crystaline dmt freebase will turn a little yellow when it melts.

This seems most likely as the intensity of the yield has been verified :shock:

Which leads me to another concern. SWIM lacking in appropriate weighing apparatus, and being over eager to make it into hyperspace, backed a bulb WAY to full. Now there is a ridiculous amount of crystal remaining in the bulb and he is wondering how long the crystals will last before oxidising. Is it worth try to scrap them out?

If he had a camera he would take a pic to provide some laughs, becuase he thinks it is more than someone would hit in 5 sittings...:lol: 8)
 
It will be fine to leave in the bulb, for a long while, but not sure how long, as SWIM has never left it sit out for more than a week or so.
 
Back
Top Bottom