space face
AND THIS IS WHY!
Hey I am new to this forum and need some advice. I have 350 mg of n,n-dmt and would like to vape it as efficiantly as possible. I've only had smokable dmt in my life once before and that was when I had a large amount at electric forest festival and honestly didn't care how I smoked it because I had so much. I was honestly really dumb about it, putting .3 in the bowl at a time and basically just burning most of it I'm sure (even though it was more than sufficiant for breaking through). Anyway this time around I can't be so careless and need the most effective way to vape what I have now. My original method for trying out this batch was with a glass bottom bowl for oils and a heat rod. It wasn't what I was looking for to say the least.
When I tried it I scaled out 30 mg of deemsters and placed it in the bottom of the bowl. I heated the heat rod with a propane torch untill the tip was just glowing red. When I touched the rod to the crystals a lot of smoke was prduced (not vapor). Also a good amount of the product stuck to the bottom of the rod and continued burning even after my lungs were full and I was trying to hold in the hit, thus wasting more product. By the time I was ready for the second hit the rod had stopped smoking and wasn't hot enough to vape any more of it. This shot was a misfire. I barely had visuals but was washed over with a strong body sensation and profound euphoria.
It looked as if about half of the material was still in the bowl, and I'm assuming that about half of what was actually burnt was smoked and not vaporized. So I'm assuming I got about a 7-8 mg hit with that method lol. Not good. So my next idea is kinda out there but I think it could be highly effeciant and a worthwhile way to smoke spice. The idea is, using my bong, I cover the bottom half of the bowl with cannabis, and then put a layer of copper ribbon or steel wool(same thing used in the machine) on top of that, and then placed the dmt on that, and then put a second layer of copper or steel wool on top of the first one containing the deemsters.
Then I would just use a lighter or torch (which would be better?) to milk the bong and take the whole dose in one hit. The cannabis on the bottom would serve to catch or soak up any spice that makes it through the bottom layer of steel or copper. So let me know, do you think that sandwhiching dmt between steel wool or copper and putting it on top of a bowl in my bong will result in an efficiant method of administration? Thanks I know this is long esspecially for a first post but any help is greatly appreciated!
When I tried it I scaled out 30 mg of deemsters and placed it in the bottom of the bowl. I heated the heat rod with a propane torch untill the tip was just glowing red. When I touched the rod to the crystals a lot of smoke was prduced (not vapor). Also a good amount of the product stuck to the bottom of the rod and continued burning even after my lungs were full and I was trying to hold in the hit, thus wasting more product. By the time I was ready for the second hit the rod had stopped smoking and wasn't hot enough to vape any more of it. This shot was a misfire. I barely had visuals but was washed over with a strong body sensation and profound euphoria.
It looked as if about half of the material was still in the bowl, and I'm assuming that about half of what was actually burnt was smoked and not vaporized. So I'm assuming I got about a 7-8 mg hit with that method lol. Not good. So my next idea is kinda out there but I think it could be highly effeciant and a worthwhile way to smoke spice. The idea is, using my bong, I cover the bottom half of the bowl with cannabis, and then put a layer of copper ribbon or steel wool(same thing used in the machine) on top of that, and then placed the dmt on that, and then put a second layer of copper or steel wool on top of the first one containing the deemsters.
Then I would just use a lighter or torch (which would be better?) to milk the bong and take the whole dose in one hit. The cannabis on the bottom would serve to catch or soak up any spice that makes it through the bottom layer of steel or copper. So let me know, do you think that sandwhiching dmt between steel wool or copper and putting it on top of a bowl in my bong will result in an efficiant method of administration? Thanks I know this is long esspecially for a first post but any help is greatly appreciated!
