• Members of the previous forum can retrieve their temporary password here, (login and check your PM).

plenty vape owners!... .making plenty vaporizer work well with dmt!!

1Starway7

Titanium Teammate
Joined
Feb 7, 2024
Messages
477
Merits
3,839
for long time i as many other owners of the plenty desk top vape ... have found problems with vapeing spice in the unit because it often took way too much spice... that led to a waste of product...
so...just did another test with my plenty desk top and am impressed at results using only two drops of spice tincture!
by reducing the size of bowl and capping the top of the heater .... i managed to compleatly vaporize a very tiny amount of spice... and felt the effecs...the vapor was ...clean...and light as a cloud ..i would say close to high quality convection.
the vapor did not have the heavy acidic taste at all could not even taste it...pictures comming.. plenty vapor is almost a match to the volcanos high quality vapor...
i think the problem with plenty was it had large air leaks on top...the air leaked around the screw on plastic bowl holders and stem connection...

in photo below you will see the experamental mini bowl within a bowl...[using crushed stainless steel scrubber pad material heated untill clean [to hold the drops of tincture]]]....[bottels of tincture]...and crude cap off device. under mini bowl]]]. also... plenty vapes .. two peice mostly plastic bowl asembily ... that is responsible for leaking lots of air into the mix when taking hit..

more to come...
 

Attachments

  • DSC02014.JPG
    DSC02014.JPG
    826 KB · Views: 13
Last edited:
Interesting and cool. I plan to pick up a type of subohm vape eventually. I'm debating on if i want to use citrate or play it safer and use freebase since freebase doesn't produce toxic compounds (though, citrate produces the least toxins compared to other dmt salts)
 
Interesting and cool. I plan to pick up a type of subohm vape eventually. I'm debating on if i want to use citrate or play it safer and use freebase since freebase doesn't produce toxic compounds (though, citrate produces the least toxins compared to other dmt salts)
NEVER vape a citrate! ..it could be very irratating on the lungs! ...stick with freebase ...if you want true convection...get a quality vaporizer like... plenty...or volcano...or atleast a lower price vape that will deliver 85 percent convection...like the [Arizer x Q2 extreem]
 
Last edited:
one reason for this test is HARM REDUCTION!!...here is a crude way im testing its performance ..by capping off the top of heater in the vape..the two holes i drilled a week ago to keep it on the top..but realized i didnt need to screw it on tight!!:unsure: ..all i need to do is set it to right temperature and alow the plenty to heat up ..then when it heats up and clicks off....
Then!.... i simply place the steel ...[ cap /off.].... .carefully on top of heater holding it on gently /tight..wait another 60 seconds and simply take a draw....[im not using the regular plastic screw on bowl] because it leaks too much air into the spice to vape properly....[although its ok for pot and many herbs] to use the stock bowl... this is just a crude test to prove it works for convection vapor.. in pictures 2022//2023//2024...after the heater reaches your choice of temperature and clicks off.
you simply connect the dab water pipe onto the mini bowl buy using a short silicone connector ..then wait 1 more minute!... till the pipe gets a little hotter....then take a draw of clean super light as a cloud convection vapor!:giggle: ...the more product in the bowl.... the thicker the vapor should be!.:alien:... .more steps comming to improve the seal under the steel cap ..... and any other ideas i come up with..
using plenty this way with freebase should work great...dont underestimate convection vapor!!

ps...i was using the max setting.... number 7 .... . but after this test i think i may be able to use lower setting like posibly 5 1/2 to get results...

im waiting to find a small stainless steel funnel.... [that fits very close over the top mouth of the heater].........i think the funnel will work best!! ...simply...place the funnel over the top of the heater after it reaches temperature /clicks off.....wait one minute...then take a hit or two ..then remove the funnel from top of heater..no harm done to the plenty desk top vape!:)

ps...just discovered just holding the pipe connector on top of heater [by hand]...may still leak too much air into the mix..? i could use the two screws i have to screw it down tighter..but dont want to ...because it builds up heat in the chamber and want to remove the pipe from top of heater fas as posible!... to go easy on the vape... have idea will share in pictures soon..

idea..[ if i have the two screws holding the bottom of pipe onto the top of heater.....after vaping...could just quickly remove the glass pipe and rubber connector and scrubber pad..and the ..hot air. will release out the hole in the bowl...reducing any chance of damage to unit... but i have an even better idea will test and share soon...

this is how i built my set up...this all depends on how your build looks and fits over the heater top...mine is just a block off to prevent heat loss and pull the hot air through a small bowl [and of corse keeping out as much outside air as posible from comming in... and ruining the convection process..
 

Attachments

  • DSC02019.JPG
    DSC02019.JPG
    488.9 KB · Views: 12
  • DSC02020.JPG
    DSC02020.JPG
    760.3 KB · Views: 12
  • DSC02021.JPG
    DSC02021.JPG
    623.7 KB · Views: 13
  • DSC02022.JPG
    DSC02022.JPG
    687.7 KB · Views: 13
  • DSC02023.JPG
    DSC02023.JPG
    596.6 KB · Views: 13
  • DSC02024.JPG
    DSC02024.JPG
    555.7 KB · Views: 12
  • DSC02029.JPG
    DSC02029.JPG
    536.9 KB · Views: 5
  • DSC02027.JPG
    DSC02027.JPG
    556 KB · Views: 5
  • DSC02032.JPG
    DSC02032.JPG
    638.5 KB · Views: 5
  • DSC02033.JPG
    DSC02033.JPG
    522.2 KB · Views: 5
Last edited:
What do you make your tincture out of?
It was made out of grain alcohol ..and mimosa spice crystals...i dont have the exact dosage figured out per drop of tincture.. i have an

idea how strong it is .. by first vaping 2 drops of spice tincture after evaporating out the alcohol.. the way i make tincture its usually 1

to 3 mgs of spice per drop...but it can be mixed much stronger... thats why one trys the low dose first..


MAIN THING!.... is closing off the top of the heater as tightly as posible... either after its heated to set temp ... or before its heated up

..i just set it on top blocking the heat inside the heater ..i choose to wait 60 seconds longer before taking hit through my bubbler pipe...

leave the top off as it heats up.. then when it clicks off ..i put the the pipe cap over it...then wait 60 seconds more [for it to get a little

hotter]....but ..[ you may or may not need to waite the 60 seconds for the clean convection heat..... early in testing..and i think its posible you will be able to set the heat to a lower setting ..[maybe 5..1/2 . on dial?]....

.early on... the reason i set it at max 7 because it was easlier to over ride the large air leaks on the origional bowl setup..

.if you do it this way ..you should notice a dryer lighter vapor thats not as acid and heavy as other vapors from other vapes....i personally on low doses notice a more gentle freindly positive effect from this convection vapor... low dose convection... puts me in a good positive mood. kinda like taking a walk on a sunny day through the green countryside ..but....this vapor can be very strong!... cheers.

NOTE.......!!...the unit should work well .....but first set the numbers 5...6...7... use a meat temperature spike tester....[not infra red]..... to test the true temperatures that it reads...some plentys did not reach the temps they were suposed to..and people had to send them back for repair...or open the case and file off the stop on the plastic temperature setting wheel...then mark a number 8 on the wheel to force it to reach higher temperatures... i think you need 360f to 400f to vape spice correctly...!

WELL.:giggle:..i tryed it with 4 or 5 drops of tincture ..it was a very low dose ..setting it first at 6 on temperature.. dial then at 7 ...it produced constant vapor at booth settings .........[no more pulling in light whisps of vapor with a lot of air]!!.........it was very light but constant convection vapor.!.. [because the dose was light].. i used the plastic orange cap to hold the experimental pipe down better on the heater.. i let it heat up.....then counted 60 seconds on number 6.......let number 7 heat up and only counted 20 seconds... they booth
produced vapor you coud see in the glass pipe and easily see blowing it out if you didnt hold it in long...

i also checked the plentys temperature out put first.... its fine:alien:... up to 390f on position 7....on position 6 a bit lower...

also!!1.. dont use an infrared thermometer.... the metal inside the heater causes inacurate infrared temp reading ..

.i used a digital meat thermometor with a long pointed temp sensor... it was more acurate...if you test your temp remember it will be much hotter reading when taking a draw.....
 

Attachments

  • DSC02025.JPG
    DSC02025.JPG
    624.9 KB · Views: 4
Last edited:
It was made out of grain alcohol ..and mimosa spice crystals...i dont have the exact dosage figured out per drop of tincture.. i have an

idea how strong it is .. by first vaping 2 drops of spice tincture after evaporating out the alcohol.. the way i make tincture its usually 1

to 3 mgs of spice per drop...but it can be mixed much stronger... thats why one trys the low dose first..


MAIN THING!.... is closing off the top of the heater as tightly as posible... either after its heated to set temp ... or before its heated up

..i just set it on top blocking the heat inside the heater ..i choose to wait 60 seconds longer before taking hit through my bubbler pipe...

leave the top off as it heats up.. then when it clicks off ..i put the the pipe cap over it...then wait 60 seconds more [for it to get a little

hotter]....but ..[ you may or may not need to waite the 60 seconds for the clean convection heat..... early in testing..and i think its posible you will be able to set the heat to a lower setting ..[maybe 5..1/2 . on dial?]....

.early on... the reason i set it at max 7 because it was easlier to over ride the large air leaks on the origional bowl setup..

.if you do it this way ..you should notice a dryer lighter vapor thats not as acid and heavy as other vapors from other vapes....i personally on low doses notice a more gentle freindly positive effect from this convection vapor... low dose convection... puts me in a good positive mood. kinda like taking a walk on a sunny day through the green countryside ..but....this vapor can be very strong!... cheers.

NOTE.......!!...the unit should work well .....but first set the numbers 5...6...7... use a meat temperature spike tester....[not infra red]..... to test the true temperatures that it reads...some plentys did not reach the temps they were suposed to..and people had to send them back for repair...or open the case and file off the stop on the plastic temperature setting wheel...then mark a number 8 on the wheel to force it to reach higher temperatures... i think you need 360f to 400f to vape spice correctly...!

WELL.:giggle:..i tryed it with 4 or 5 drops of tincture ..it was a very low dose ..setting it first at 6 on temperature.. dial then at 7 ...it produced constant vapor at booth settings .........[no more pulling in light whisps of vapor with a lot of air]!!.........it was very light but constant convection vapor.!.. [because the dose was light].. i used the plastic orange cap to hold the experimental pipe down better on the heater.. i let it heat up.....then counted 60 seconds on number 6.......let number 7 heat up and only counted 20 seconds... they booth
produced vapor you coud see in the glass pipe and easily see blowing it out if you didnt hold it in long...

i also checked the plentys temperature out put first.... its fine:alien:... up to 390f on position 7....on position 6 a bit lower...

also!!1.. dont use an infrared thermometer.... the metal inside the heater causes inacurate infrared temp reading ..

.i used a digital meat thermometor with a long pointed temp sensor... it was more acurate...if you test your temp remember it will be much hotter reading when taking a draw.....
if a normal dose of spice 20 to 30 mgs were put in the bowl ..vaped it should be amazingly potent! without any acid taste just light convection vapor! inhaling this kind of vapor is like inhaling air ! if product is reasonably pure....no iratation to throat or lungs....
inhaling this kind of light vapor is easy to over due it ...less is more with convection vapor..:giggle:
 
Last edited:
if a normal dose of spice 20 to 30 mgs were put in the bowl ..vaped it should be amazingly potent! without any acid taste just light convection vapor! inhaling this kind of vapor is like inhaling air ! if product is reasonably pure....no iratation to throat or lungs....
inhaling this kind of light vapor is easy to over due it ...less is more with convection vapor..:giggle:
ok i figured out how to hold the bottom of my pipe down on top of the heater withoiut using screws and not hurting the plenty vape at all!!

luckily...I had an extra plenty black cap from my old plenty and i cut out the center out and a little bit underneath...now all i do is lay the pipe bottom down over the heater top... then put the screw on cap over the bowl asembly give it a ltlle twist and the bowl and cover is

on the pipe like it was made for it screws on level and snug preventing any loss of hot air heat.. and it can be removed quickly to alow the plenty to cool down fast!:giggle:

i found the plastic is very heat resistant ..i couldent melt through it with a red hot razor blade! i had to drill little holes in a circle then use a dremel to smooth out the edges of the hole in center of black cap.

for people who dont have an extra cap...they can measure their existing cap ...or take it with them to a food store and match the measurments up to a screw on cap from a food product...then if it fits and will screw on.... cut the middle out of that cap to use as a hold down...

i personally think that using the origional .... plenty black twist on cap.... is best choice... because its very heat resistant and very strong..simply order a new black cap. and cut a hole in center as i did..

just.. simply order an extra black plastic plenty vape cap...and use it as i did mine...

NOW cap is easily twisted off... and good news...there is no damage done to the vape! ..one can use the factory bowl asembly as it was intended....

the twist on bowl retainer will now hold the thin steel cover ...evenly.... down on top of heater ..[letting the hot air build up below near the heating block.... and preventing valuable heat loss.... so hard to vape... products can now be vaped properly with good results!.... producing high quality... Stores and bickel plenty convection vapor.!...also no damage to vape because you can ...quickly after vaping... twist off the hold down cap alowing the heat to leave the unit fast!... preventing any heat damage!

.....the twist on cap........is much better than my earlier idea of holding down the heat cover with two small screws!
faster and safer... removal of heat cover!


question? just how the steel bowl connected to the round thin steel cover?

answer..[concidering i had no welder].....the bowl was from another vaporizer..i cut the stem below the bowl short ...then stuck it through the hole in in middel of heat cover .... then flared the short steel stem ...and gently hammered the flared metal untill it was strongly connected,,,[like being rivited] you can see this in picture 2029...:unsure:



hmm..:unsure: i may remove the center brass bowl ....[it is kinda small]....and use the medium sized steel bowl around it?... if the heater bowl cover is sealing well enough on top... . .the plenty vape.. should have enough convection heat to heat up a 3/4 in steel bowl easily..
The steel bowl is from the first wooden vapor genie years ago! :alien:
 

Attachments

  • DSC02034.JPG
    DSC02034.JPG
    543.8 KB · Views: 11
  • DSC02035.JPG
    DSC02035.JPG
    699.3 KB · Views: 11
  • DSC02036.JPG
    DSC02036.JPG
    594.9 KB · Views: 10
  • DSC02038.JPG
    DSC02038.JPG
    472.7 KB · Views: 10
  • DSC02042.JPG
    DSC02042.JPG
    676.1 KB · Views: 9
  • DSC02029.JPG
    DSC02029.JPG
    536.9 KB · Views: 5
Last edited:
ok i figured out how to hold the bottom of my pipe down on top of the heater withoiut using screws and not hurting the plenty vape at all!!

luckily...I had an extra plenty black cap from my old plenty and i cut out the center out and a little bit underneath...now all i do is lay the pipe bottom down over the heater top... then put the screw on cap over the bowl asembly give it a ltlle twist and the bowl and cover is

on the pipe like it was made for it screws on level and snug preventing any loss of hot air heat.. and it can be removed quickly to alow the plenty to cool down fast!:giggle:

i found the plastic is very heat resistant ..i couldent melt through it with a red hot razor blade! i had to drill little holes in a circle then use a dremel to smooth out the edges of the hole in center of black cap.

for people who dont have an extra cap...they can measure their existing cap ...or take it with them to a food store and match the measurments up to a screw on cap from a food product...then if it fits and will screw on.... cut the middle out of that cap to use as a hold down...

i personally think that using the origional .... plenty black twist on cap.... is best choice... because its very heat resistant and very strong..simply order a new black cap. and cut a hole in center as i did..

just.. simply order an extra black plastic plenty vape cap...and use it as i did mine...

NOW cap is easily twisted off... and good news...there is no damage done to the vape! ..one can use the factory bowl asembly as it was intended....

the twist on bowl retainer will now hold the thin steel cover ...evenly.... down on top of heater ..[letting the hot air build up below near the heating block.... and preventing valuable heat loss.... so hard to vape... products can now be vaped properly with good results!.... producing high quality... Stores and bickel plenty convection vapor.!...also no damage to vape because you can ...quickly after vaping... twist off the hold down cap alowing the heat to leave the unit fast!... preventing any heat damage!

.....the twist on cap........is much better than my earlier idea of holding down the heat cover with two small screws!
faster and safer... removal of heat cover!


question? just how the steel bowl connected to the round thin steel cover?

answer..[concidering i had no welder].....the bowl was from another vaporizer..i cut the stem below the bowl short ...then stuck it through the hole in in middel of heat cover .... then flared the short steel stem ...and gently hammered the flared metal untill it was strongly connected,,,[like being rivited] you can see this in picture 2029...:unsure:



hmm..:unsure: i may remove the center brass bowl ....[it is kinda small]....and use the medium sized steel bowl around it?... if the heater bowl cover is sealing well enough on top... . .the plenty vape.. should have enough convection heat to heat up a 3/4 in steel bowl easily..
The steel bowl is from the first wooden vapor genie years ago! :alien:
im trying something a little different....i tested this glass atachment on plenty 2 times ...without the scrubber pad...this time using 2 or 3 layers of screen and the larger steel bowl...using temperature number 6 ..... the vaper came rooling up trough the glass tube...😍
but need to hook it up to my bubbler pipe to cool it down...
 

Attachments

  • DSC02044.JPG
    DSC02044.JPG
    666.2 KB · Views: 8
  • DSC02043.JPG
    DSC02043.JPG
    565.3 KB · Views: 8
  • DSC02048.JPG
    DSC02048.JPG
    750.2 KB · Views: 7
  • DSC02049.JPG
    DSC02049.JPG
    465.1 KB · Views: 7
  • DSC02047.JPG
    DSC02047.JPG
    894.8 KB · Views: 5
Last edited:
thiis whole thing is trial and error......and is getting more complicated than i like......i just worked out a ....another more simpler way!.... to make plenty work well.... it very much like myE mesh build... forget every thing above...

Everything needed can be done using the existing black cap .. without altering anything! ..... so [DONT] !!.....cut a hole in the cap ! please

wait..i will show how it should work well...it involves putting a ...[compresion formed screen bowl] inside the tube in the black cap and maybe a little fileing...
 
Last edited:
ok.... here are some pictures of my idea...this has already proven to work with my E mesh convection build!......the difference with the plenty
compaired to e mesh is the very pure controled heated air being pulled through the adustable compressed screen bowl ..it may take a minute for the plenty desk top to click off... [meaning its reached the set heat range]...then wait another 30 seconds to a minute for heat

inside to rise a little more..then take a draw
this cap can be used..... [without any damage to it]...by compressing a screen bowl into the shaft ... and adding a couple finer screens on

top of the first coarser screen...using the... first coarser screen ... to create some drag inside the shaft .... so it will stay where its put.... or raised up or down.... using the erasser end of a pensil as a way of minor heat adjustment...the rest of the shaft above the screen bowl

can be used to fit a snug fitting pipe stem so the hot air can be pulled through the product in the screen bowl...
[[exactly like my convection E mesh build !!]... it works the same... only the air temp is more controled in the plenty ..not an instant flash... vaporization.... as e mesh does...more of a gentle compleate vaporizaion...

to use this black cap you simply twist it onto top of heater screen ... you may need to press down harder as you twist it ..once the threads catch turn it .....a little tighter.... but not too far!!.....it should stay locked on top of heater.. one could file off the fine plastic

under the cap so it will twist on farther ...but not nessasery..just dont get too agressive tightning it ..just enough that it locks onto the heater top....

to make the compressed screen bowl.... start with a stiffer coarser pipe screen .... and press the screen into the black verticle shaft using sonething like a rod close to the dimention of the inside of shaft..press the coarser pipe screen in untill it press forms into the space inside the shaft...
then remove the newly compressed main screen and cut the top edges of even then return it into the shaft...in the black shaft there is a stop in bottom of shaft so it wont fall out...

remove the first primary screen and cut 2 or 3 finer screens to... place on top of it.... to prevent any drip down of spice as it vaporizes ....
one could ust use ss scrubber pad...but i prefere screens....

2062..2061..2059..2070..2068.. show diferent stages of making a screen bowl.... 2068 shows main screen bowl all the way down to stop..and you can see the screen was trimmed evenly.... will add 1 or 2 more finer screens on top of main screen to prevent melt /drip down.. while vaping...

NOTE!!.....when making the compressed screen bowl..the first screen is made of thicker stiffer ss wire..because after forming it .. it creates drag and stays in place......[ the main screen can be adjusted up or down a little... [or removed for cleaning].....with end of a pensil eraser].....the two extra screens are cut from a finer weave of screen ..[you dont have to compress them into the cylinder [you simply cut two round flat discs that will lay in bottom of bowl...cutting the discs ...a little ....out of round is good!! !....because when you push the flat round screen disc .. EVENLY..into the bottom of the main screen it catches the sides enough to keep it in place in bottom of screen bowl... so remember the two finer screens are simply round flat disc shaped screens that lay in bottom of bowl ..

the material that the black twist on cap is made from is amazing! it wont melt atleast from the temps comming from the plentys heater..and that means its safe to vape with because there should be no ...,off gassing!
..... regular plastic would melt and deform from the heat!
this material in the black cap.. is like plastic metal it resists heat .. can be ...drilled....filed....or.. cut with saw......but... wont melt...
Storz and Bickel.....the makers of the ...plenty and volcano vapes would not use it ..if it wasnt safe!


The black twist-on top piece (the Filling Chamber Housing and Cap) of the Storz & Bickel PLENTY is made of medical-grade PEEK (polyether ether ketone)—a high-performance thermoplastic engineered specifically to withstand extreme heat without melting or off-gassing....THIS MEANS SAFTEY!!..harm reduction for vape user...
 

Attachments

  • DSC02054.JPG
    DSC02054.JPG
    617.8 KB · Views: 8
  • DSC02053.JPG
    DSC02053.JPG
    592.3 KB · Views: 8
  • DSC02058.JPG
    DSC02058.JPG
    663 KB · Views: 8
  • DSC02057.JPG
    DSC02057.JPG
    609.2 KB · Views: 8
  • DSC02062.JPG
    DSC02062.JPG
    625.5 KB · Views: 6
  • DSC02061.JPG
    DSC02061.JPG
    520.1 KB · Views: 6
  • DSC02059.JPG
    DSC02059.JPG
    572 KB · Views: 6
  • DSC02070.JPG
    DSC02070.JPG
    573.8 KB · Views: 7
  • DSC02068.JPG
    DSC02068.JPG
    711.6 KB · Views: 8
Last edited:
since this is a trial and error effort..this may be boiling down to ....[the max temperature the plenty puts out]......i measured 280f ..but figured that when someone takes a pull the temp should rise some...

i measured the temp the other day set on max setting no 7 and it read around 280 f ...but thats without taking a draw ...
book says spice needs something over 300 f to vape correctly...

The temp should be hot enough that when the hot air is pulled through the spice..it should explode into vapor much like the conduction e mesh... and my convection E mesh does...

ive tryed a few ways and had some partial success and may have to force the vape to put out a higher temp... by taking the cover off and fileing off the orange temperature dial stop ... so the dial can turn just a little farther .. to say]...an imagenary number 8.. it may only take

turning the dial half way to 8.... the to get the increased temperature i need...?
will try the black cap bowl set up on number 7 this time last attempts were on number 6...

the plenty uses a lower tec thermostat with a spring in it.... its pretty simple...increase the spring tension more and it stays on longer. reaching a higher temp...only thing is.... dont go too much higher..!. turn it up an few incraments at a time and take its temp...

all this above is about making the vape work with freebase...

[but ive read.]]...... its posible to use a carrier herb and make CHANGA]...work well with the plentys standard equpiment without changing anything..

. In my opinion....i still think the temp is close.... but a still little low...
 
Last edited:
since this is a trial and error effort..this may be boiling down to ....[the max temperature the plenty puts out]......i measured 280f ..but figured that when someone takes a pull the temp should rise some...

i measured the temp the other day set on max setting no 7 and it read around 280 f ...but thats without taking a draw ...
book says spice needs something over 300 f to vape correctly...

The temp should be hot enough that when the hot air is pulled through the spice..it should explode into vapor much like the conduction e mesh... and my convection E mesh does...

ive tryed a few ways and had some partial success and may have to force the vape to put out a higher temp... by taking the cover off and fileing off the orange temperature dial stop ... so the dial can turn just a little farther .. to say]...an imagenary number 8.. it may only take

turning the dial half way to 8.... the to get the increased temperature i need...?
will try the black cap bowl set up on number 7 this time last attempts were on number 6...

the plenty uses a lower tec thermostat with a spring in it.... its pretty simple...increase the spring tension more and it stays on longer. reaching a higher temp...only thing is.... dont go too much higher..!. turn it up an few incraments at a time and take its temp...

all this above is about making the vape work with freebase...

[but ive read.]]...... its posible to use a carrier herb and make CHANGA]...work well with the plentys standard equpiment without changing anything..

. In my opinion....i still think the temp is close.... but a still little low...
well i tryed the highest position 7 on the temp dial .... [increasing the temp made a positive!! difference]:)... ..there was just some light residue left on the screen bowl and i used the....[ black cap with [screen bowl] set up.... that sits about 2/3rds of an inch above the

heating screen on top of heater..


i felt a gental low level spice buzz....then layed down listened to some piano music ...and seemed to enjoy it more than usual..
i even experianced closed eye visuals although weak..they were apearing along with positive emotional drift that colored the visuals...and blended into the music...

i would just use the black cap with the screen bowl pushed into the bottom...[pictures 2068 2070]].....the screen sits about 2/3rds of an inch above the coarse heater screen... make shure you have 1 or 2 finer screens on top of the coarser base screen to prevent drip down...

MAKE SHURE THE THIN CIRCULAR AREA .in center ....under the black cap [picture 2070]]..[zoom picture and see a thin circular ring] . makes ...[solid even contact]...[seals].... with the flat circular aluminum ring thats around the screen... make shure you twist the black cap reasonably tight!!..[but dont break it]... preventing any outside air from entering the vaping chamber above...because outside air may delute the vapor too much...

ps. warning.... I thought the thin circular ring under black cap..[2070]..was a little thin to seal out external air.. so i layed it on ..[a very flat surface] with some medium fine sand paper and sanded the circle down,,, [only a little] to create a slightly wider surface to seal out air from entering...i almost went too far with the sanding!. [on flat surface] ... if one sands too much it make make it worse for blocking out external air from entering the chamber!!

so far im using a very low dose.... just testing it out...if a more normal 15 to 30 mg dose were used your going to get much more vapor!:alien:

ive heard the other way is to make ..[CHANGA]... it may work with the basic stock setup because the herb carries and prevets drip down....
i just wanted to use lower doses of the more pure free base...




....below in picture 2071...the end of wire is resting on ....the thin edge..... that makes contact with round aluminum cap on top of heater that will block out extra external air from entering vaping bowl area...

i sanded mine down a little too far!... on flat surface..trying to make a wider surface area to block air from entering the bowl during vaporization... after twisting it on tight ....if im lucky]].....i think it is still making contact blocking extra air?! [if it caused an extra air leak i will have to use a thin aluminum washer.....

DONT make this mistake!!... if you do sand it down ...[a little]..small incraments at a time ...on flat surface ..go just a little at a time then twist cap on making shure its contacting top of aluminum ring on top of heater solidly!

ACTUALLY....its best not to sand it at all! ..if you can press down solidly ...and twist the threads will start a little and at least hold it down without changing anything....

sent this picture so you can see what im talking about...zoom picture to see it close..



ps...... for those who want e mesh convection...this pipe works exelent producing milky white convection vapor about as fast as conduction e mesh...click address below...

the reason im working on the ..[stores and bickel]... plenty vape... is because i feel the vapor quality is a couple notches higher quality...


convection vape improved by air tight rubber connector
 

Attachments

  • DSC02070.JPG
    DSC02070.JPG
    573.8 KB · Views: 8
  • DSC02068.JPG
    DSC02068.JPG
    711.6 KB · Views: 8
  • DSC02071.JPG
    DSC02071.JPG
    571.1 KB · Views: 5
Last edited:
Hey People! SUCESS!.... this works well! using the black cap method to vape even for the tinyest doses! ...This convection wastes NOTHING using the plenty!!
I tryed again set to max temp...i was in no hurry and used a tiny dose of 5 drops of tincture the alcohol was evaporated within an hour but waited till next morning shined a light into the bowl could see little golden specks all over the three layer screen..if i had magnification one would see crystals...

set on max number 7 on temp dial... i waited till it cllicked off and put plug ... ... over the top of the black cap,,, to hold the heat inside it longer...it prevents any heat loss.... then waited 30 seconds more...removed the [heat plug] .... put my pipe stem into it and took a slow long draw through the bubbler...
This time...there was more constant vapor ! ...... ,. no more tiny wisps of vapor with a lot of air.......i think this setup using the black cap to hold the 3 layer screen bowl ...the main bottom screen...then two finer screens on top of it..to slow any drip down...

this test was only 5 drops of tincture...that equals only 3 to 5 mgs of freebase!!,.... it didnt waste any of it! i can imagen how 20 to 30 mgs would hit..
the vapor was so light and clean seemed quite pure! i detected no acidic tase at all.... this screen set up in picture 2068 with two added finer screens on top of main screen...will vape tincture...or crystal...easily and the controled heat produces clean vapor!

i think this is posible because i iliminated the extra air leakes,,, by putting the bowl closer to heat source..and also using a much smaller bowl...and the highest setting....
this was not posible in the past with plenty desk top vape...if it worked back then you would have to waste a lot of spice to get a minor effect...now this way it works good with free base....and retains its stores and bickel convection quality

even testing with such a low tiny dose..i got some nice distant but nice closed eye visuals...with the music it was a golden
experiance!
if someone replicates this set up please report your experiance!:)
 

Attachments

  • DSC02068.JPG
    DSC02068.JPG
    711.6 KB · Views: 8
  • DSC02072.JPG
    DSC02072.JPG
    683.5 KB · Views: 5
  • DSC02074.JPG
    DSC02074.JPG
    801.2 KB · Views: 5
  • DSC02075.JPG
    DSC02075.JPG
    723 KB · Views: 4
  • DSC02076.JPG
    DSC02076.JPG
    810.6 KB · Views: 4
  • DSC02088.JPG
    DSC02088.JPG
    721.9 KB · Views: 6
  • DSC02093.JPG
    DSC02093.JPG
    634.6 KB · Views: 6
Last edited:
Back
Top Bottom