the goo, it it safe to use?

[Trousercheese]

1. Ive done mhrb pulls before and had some come out dry, but usually it looks like it's going to be good, then melts away into oily substance as it dries. I'm assuming fat. This is with a pre freeze wash too where i dumped and swirled distilled water into the sucked off layer, to get out lye and other crap. Normally I just throw it away if it's oily. But, Is it still vape usable safely? So long as it's not sol? Just seems to be fat.! Remaining Sol (solvent) dries fast even it's dumped out. And stuck to the sides. And a blow dryer on low heat should dry it. But it just makes it wet and oily. I could recrystalize, but don't have time.

2. I did something different this time and more patience, and am seeing a ton of stuff suspended in the yellow sucked off solution. Cloudy, milky. After wash (3 or 4 squirts of water) before freezer. Is this the molecule? Do I want to filter it out? It doesn't stick to the sides of the glass but it sure looks like what I think it is. What else could it even be? What would happen if I just used it?

Thanks!

 

[Trousercheese]

Shouldn't the goo be fixable with some distilled water swirled? If it's the bad stuff, it should be insol in solvent, soluble in water right? Swirl a little warm water, dump and redry.

 

[Trousercheese]

Ok I just finally found a thread that says the goo is safe. Nm.

 

[RitualOpossum]

Goo is great for changa and enhanced leaf but I'm not sure if goo works the best or not in vapes? Really unsure. To Make enhanced leaf/changa

Use a bit of solvent like acetone or very high % isopropyl alcohol. Carefully weigh the herbs you will use - write it down. Put the freebase goo into a shot glass. Put that shot glass into a pan of hot water. Now use a dropper to add single drops of solvent until everything is uniform solution (may take a lot of drops). Now add the herbs. Stir well. Evaporate the solvent fully. Now weigh the herbs. This new weight minus the original weight of the herbs is the weight of the goo and you can use this to judge how much weight to put into the GVG of your enhanced leaf.

Pandora taught me this

 

[bezevo]

Learning stuff is cool !

You should take some time and read up on the polymorfic natchure of nnDMT .

nnDMT CAN be in many forms because it is polymorfic . i

It can be a white powder small white crystals , it can be many shades yellow , orange , it can be waxy oily or goo and all of these can be 97% nnDMT OR More ,
It is a myth that white is more pure ,

It can even be red oil or goo , that is right the so called magical mystery substance the used to be called JUNGLE SPICE is just another polymorfic vaiation of nnDMT .

good luck

 

[Trousercheese]

Goo is great for changa and enhanced leaf but I'm not sure if goo works the best or not in vapes? Really unsure. To Make enhanced leaf/changa

Use a bit of solvent like acetone or very high % isopropyl alcohol. Carefully weigh the herbs you will use - write it down. Put the freebase goo into a shot glass. Put that shot glass into a pan of hot water. Now use a dropper to add single drops of solvent until everything is uniform solution (may take a lot of drops). Now add the herbs. Stir well. Evaporate the solvent fully. Now weigh the herbs. This new weight minus the original weight of the herbs is the weight of the goo and you can use this to judge how much weight to put into the GVG of your enhanced leaf.

Pandora taught me thii

It worked ok. No clogged vape. Burns fine and tastes fine. Makes my throat itch like hay fever in springtime pollen, but not terrible. Probably has the shit in it that the trees give off that makes me sneeze in the spring.

Batch 2 was nice and dry. No goo. Dunno what's different. Pretty much made it the same way. The wash before the freezer with distilled water I was gentler with. I used more water more times with less agitation. 4 washes with 10 or 20 ml and light swirl. Let settle and release. Only did 2 agitated ones the first time. Also, I started the second 50g pull letting the powder sit in the straight vinegar for a few minutes before adding the 200ml hot water. (Cybs tek based tek). I also took foil and inched a shitload of tiny holes in it with a 32 gauge insulin syringe and then put it on top of a paper coffee filter trimmed as small as possible to avoid absorption to try and catch crystals on the foil, as the paper is impossible to get them out if. It didn't work in that regard but I got perfectly dried crystals in the end without oil.

 

[TransistorBass]

Great name btw.... do you make your own Trouser Cheese?
Raw or Pasteurized?