• Members of the previous forum can retrieve their temporary password here, (login and check your PM).

Increasing the yield of DMT extractions by using methanol.

Migrated topic.

imagine13

Rising Star
Joined
Sep 22, 2012
Messages
66
Merits
42
1) STB - using large excess of white spirit (good, selective solvent for DMT)
2) add small amount of methanol (mixes at room temperature) and put in freezer (forms two layers)
3) separate methanol layer and add oxalic acid dissolved in methanol (DMT oxalate precipitates)
4) recrystallize DMT oxalate from the methanol
5) dissolve in 20% or higher ammonia, and extract into DCM
6) pure DMT
 
You make a good first impression.

I bet your a people person.

And we can already get 2% yields with good old salt.
 
I'm curious what his advice was. Not sure how it would increase the amount of DMT in the source plant though, AFAIK the existing teks if followed correctly already pull out more or less all that's in the plant.
 
Sorry, I got banned from bluelight so I was in a bad mood! Rather than be a complete arse:
1) STB - using large excess of white spirit (good, selective solvent for DMT)
2) add small amount of methanol (mixes at room temperature) and put in freezer (forms two layers)
3) separate methanol layer and add oxalic acid dissolved in methanol (DMT oxalate precipitates)
4) recrystallize DMT oxalate from the methanol
5) dissolve in 20% or higher ammonia, and extract into DCM
6) pure DMT
7) apologize
 
imagine13 said:
Sorry, I got banned from bluelight so I was in a bad mood!

Good call benzyme!

Interesting process imagine. I don't know enough about it to know how effective it is. Probably worth a shot though.
 
All I can tell you is that my yields have increased by a third; and that the product is much purer due to the selectivity of the DMT oxalate recrystallization step (from methanol). Instead of using ammonia and DCM, one can also just add sodium hydroxide and water (sodium oxalate precipitates) and extract into naphtha.
Alternatively, again, one may add to the methanol twice the volume of water and a small dash of sodium hydroxide; and extract the DMT that precipitates with whatever solvent you like.

It won't increase the yield if you're already using DCM, I suppose, but it simply improves the ease of operation in practice, I find - with no solvents to distill; and complete recovery of the naphtha.
 
Hey imagine13, maybe post an introduction essay in the new member area.

The Nexus is a wonderful place.

And just so you know Benzyme is a baller chemist who is highly respected around the nexus.
If you have numbers and maybe side-by-side data, it might help back your claim.

Stating things as complete fact on the nexus is kinda frowned upon.

Asking questions about a potential new method to increase yield is usually a good idea.
The chemistry folks are always willing to contribute their thoughts and knowledge.
Asking questions would help open the flow of conversation.

Anyway, welcome to the nexus. Be sure to check out the rules, FAQ, and other things to get an idea of what's expected of members.

:)


Oh, and its not too late to edit that first post! :d
 
And it might be polite to edit your first post again. Hard to have a dialogue with you while you are still sticking your middle finger up at us :D
 
Garyp88 said:
And it might be polite to edit your first post again. Hard to have a dialogue with you while you are still sticking your middle finger up at us :D

Lol, synchronous thoughts, we typed this within a few min of each other. 😁
 
imagine13 said:
Sorry, I got banned from bluelight so I was in a bad mood! I'll probably be banned from here before long, but rather than be a complete arse:
1) STB - using large excess of white spirit (good, selective solvent for DMT)
2) add small amount of methanol (mixes at room temperature) and put in freezer (forms two layers)
3) separate methanol layer and add oxalic acid dissolved in methanol (DMT oxalate precipitates)
4) recrystallize DMT oxalate from the methanol
5) dissolve in 20% or higher ammonia, and extract into DCM
6) pure DMT
7) apologize
8) leave!


please edit your original post, and stick around awhile. we'll edit ours accordingly.
we're always open to extraction methods. :)
this forum isn't bluelight, I know those guys can be serious d*cks. we're actually
a much more friendly community, threads don't involve new ways of cooking up meth or opiates. we're mostly about cacti, fungi, dmt, and harmalas. and iboga.

oh yeah, thanks for the kudos, wearepeople.
 
I seem to remember during my initial research for my first extraction I was told that white spirit is not good for extraction, but maybe that was because it leaves something behind in an evap and is not good for freeze precip?
 
Back
Top Bottom