psilocybin
Rising Star
Any questions or problems you may run into during an extraction can be asked to get other members input in this thread.
-
Members of the previous forum can retrieve their temporary password here, (login and check your PM).
official extraction help thread
- Thread starter psilocybin
- Start date
-
- Tags
- dmt
thanks, just got a bit of goo off my first pull of an ATB with 50g Acuminata bark, ill see how much i get off it and if i think its worth it ill try a mini a/b - have wanted to try a proper hit of the goo/spice so keen to give it a whirl. Do you think freeze precip would be better to form crystals than evaporating for any reason? I evapped this pull.
While they can both produce good results, freeze precipitation would tend to produce purer crystals, although slow evaporation is the favoured way of producing large crystals.
The main thing with evaporation is that the last remaining portion of solvent will contain a higher concentration of impurities, and a mixed solvent like naphtha will have its more volatile components evaporating in greater proportion at first. This means that the material which crystallises later on is more likely to contain impurities and trapped hydrocarbons. There may also be a bit more polymerisation later on, as a function of exposure to oxygen for a longer period.
Freeze precipitation carries the further advantage of preserving the solvent for subsequent reuse; conversely, evaporated solvent is effectively lost, unless one were going to unusual lengths to capture and condense it - something which isn't realistically feasible for the average hobbyist as the required rate of evaporation is too slow.
why not take the opportunity to try FASA? it doesnt have to specifically be fumaric acid however, i forget which other ones, pretty sure its in one of the FASA/FASI threads, but theres other, more common, acids you can use that will form a DMT salt that immediately crashes out of a NP solvent upon addition of acetone or isopropanol that has been saturated with as much of the given acid as it can hold. I think ascorbic acid (vitamin C) is one of them, regardless of if it is, ascorbate can be smoked directly. citric acid too though im pretty sure its really hygroscopic so it might not be practical without molecular sieves and a dessicator. odds are your local brew shop will have something. it was either speculated or confirmed, tartaric acid may work too, which is available at any supermarket. It is worth digging into, FASA will work with many acids, saturating many solvents.
after filtering and drying, you then dissolve in a very small amount of clean water and add some carbonate solution, and basify the carboxylic DMT salt back to the freebase we know and love.
the great thing is it fits right into an existing tek, you just use something like toluene, xylene, limonene perhaps, or another NPS that dissolves DMT too well to crystalize from, but will happily extract at room temp, in place of naptha. And instead of freeze precip or evap, you dry it (magnesium sulfate) then filter and add fumaric acid saturated acetone, which also must be dry similarly.
you can use exotic or low volatility solvents here too and just wash them out after you collect your DMT fumarate crystals. the acetone will wash out with water, as will IPA. the solvent can be re-used so much.
Later you dissolve the fumarate in a small volume of water and drip in some sodium or potassium carbonate.
That milky DMT freebase milk in the video eventually forms large clean crystals, which someone has documented and put up in the wiki.
another important aspect is that once you have your DMT fumarate, it is insanely stable in that form, kept dry and refrigerated it will last decades iirc. so if you are doing a bigger batch than youl consume for a good long while, you only have to freebase what you intend to use.
since FASA works with limonene, you can do your entire process start to finish using food-safe chemicals, or house-safe solvents, this was a remark someone made that stuck with me.
after filtering and drying, you then dissolve in a very small amount of clean water and add some carbonate solution, and basify the carboxylic DMT salt back to the freebase we know and love.
the great thing is it fits right into an existing tek, you just use something like toluene, xylene, limonene perhaps, or another NPS that dissolves DMT too well to crystalize from, but will happily extract at room temp, in place of naptha. And instead of freeze precip or evap, you dry it (magnesium sulfate) then filter and add fumaric acid saturated acetone, which also must be dry similarly.
you can use exotic or low volatility solvents here too and just wash them out after you collect your DMT fumarate crystals. the acetone will wash out with water, as will IPA. the solvent can be re-used so much.
Later you dissolve the fumarate in a small volume of water and drip in some sodium or potassium carbonate.
That milky DMT freebase milk in the video eventually forms large clean crystals, which someone has documented and put up in the wiki.
another important aspect is that once you have your DMT fumarate, it is insanely stable in that form, kept dry and refrigerated it will last decades iirc. so if you are doing a bigger batch than youl consume for a good long while, you only have to freebase what you intend to use.
since FASA works with limonene, you can do your entire process start to finish using food-safe chemicals, or house-safe solvents, this was a remark someone made that stuck with me.
I’ve been having issues with re x. I heat up the heptane in a crystalizing dish. Wait till I start to see bubbles and toss the Fb from an STB extraction. I use to get a layer of crystals on top of slag. Last few years, some of the crystals clearly get caught in the slag. I hope you guys can help me out. I use to use Doc Edingtons and never had an issue with that, but it’s been out of business for a while. I’ve tried Bestine, 99-100% heptane from Amazon and I have success here and there but can never replicate. Any help is appreciated. I’m sure I’m doing something wrong. Tried altering temp, nothing seems to help. Thank you
Attachments
Last edited:
Small detail, but it might be better to add the hot heptane to the crystals, for more precise control of the solvent ratio. There is a slight issue with the low melting point of at least one of the DMT polymorphs - and all of them melt at a lower temperature than boiling heptane, of course. In that case, a more careful addition of the right amount of FB powder to somewhat cooler heptane could bring better results. Oiling out is more likely to occur if the solvent is oversaturated. This is something that tryptamines are particularly prone to do, especially if the DMT already starts crashing out of the heptane at a temperature above its melting point.
If polymerisation has become an issue - perhaps due to the starting material, for example - you'll likely see better results if you run the initial product through a mini A/B and crystallise carefully from that.
Thanks for the insight. In the hot water bath I don’t think the heptane was up to boiling but I’ve checked it before at that point and it was 140-160. Shulgin remarked there were many different ranges of crystallization temps and my old method use to produce great white fluffy crystals. I just never use to have an issue with this. I have tried lower solvent temps and have the same issues, could be bad heptane maybe. What mini ab tek would you recommend? Also as far as basic chemistry regarding these extractions, is there somewhere I can find out about basic terminology? My chemistry knowledge is lacking for sure.
Reading it over, looks like I can pull it off. Does it matter what kind of salt? Iodized, or non-iodized? Also for the RE-X in this tek, can naptha be swapped with Heptane? Or would that cause an issue at that temp? Thanks
non-iodized
yes
