OpeningPandorasBox
Rising Star
After some more testing and tweaking I have come up with a new design which is MUCH more user friendly.
I call it The Key V2
Assembly is really about as easy as can be possible so anyone with a measurable IQ should be able to whip one up in 5 min or less and for dirt cheap as well.
While testing this version I found it to work even better and solves all of the previous designs problems. Heat is not an issue because you never have to touch the brass until its cashed but even then with its massive capacity reloads will be few and far between.
Basic Assembly instructions - Feel free to vary the sizes of fittings used as this unit was designed to vape changa. Anyone who has tried changa knows that a little changa always turns into alot of changa so I just went ahead and built it big enough to hold a BIG load. However if plain spice is going to be the main fuel then much smaller fittings could be utilized.
First you will need all of this - The screens can be bought at any smoke shop and the o ring comes with any water pipe slide. I just asked and got one for free. NOTE: The piece in the upper right with female threads on both ends appears to have been miss bagged as searching to part number brings up a different fitting. Finding the correct piece visually should not be difficult.
UPDATE: to remove any possible grease or contaminations thoroughly wash and scrub all brass pieces with acetone. Then when dry place in oven at a very high temp like 600 degrees for an hour or two. Even better yet heat each piece with a propane torch thoroughly. This should vaporize any residue on the fittings.
Then assemble as follows - I will not go into as much detail this time because if you cant figure it out your not going to be able to obtain spice anyways.
Then with this piece assembled drop in 5 screens
Now thread in the 1/8" pipe
Now take the fitting with the larger 3/8" female threads and push 5 more screens into the threads
Now just assemble the two pieces you have made
Slide on your O-ring and your done
IMPORTANT UPDATE: If you push the screens down further in the threads it works even better and still wont burn the herb even if you try!
Happy Vaping!
Please post your experiences with The Key V2
OPB
I call it The Key V2
Assembly is really about as easy as can be possible so anyone with a measurable IQ should be able to whip one up in 5 min or less and for dirt cheap as well.
While testing this version I found it to work even better and solves all of the previous designs problems. Heat is not an issue because you never have to touch the brass until its cashed but even then with its massive capacity reloads will be few and far between.
Basic Assembly instructions - Feel free to vary the sizes of fittings used as this unit was designed to vape changa. Anyone who has tried changa knows that a little changa always turns into alot of changa so I just went ahead and built it big enough to hold a BIG load. However if plain spice is going to be the main fuel then much smaller fittings could be utilized.
First you will need all of this - The screens can be bought at any smoke shop and the o ring comes with any water pipe slide. I just asked and got one for free. NOTE: The piece in the upper right with female threads on both ends appears to have been miss bagged as searching to part number brings up a different fitting. Finding the correct piece visually should not be difficult.
UPDATE: to remove any possible grease or contaminations thoroughly wash and scrub all brass pieces with acetone. Then when dry place in oven at a very high temp like 600 degrees for an hour or two. Even better yet heat each piece with a propane torch thoroughly. This should vaporize any residue on the fittings.
Then assemble as follows - I will not go into as much detail this time because if you cant figure it out your not going to be able to obtain spice anyways.
Then with this piece assembled drop in 5 screens
Now thread in the 1/8" pipe
Now take the fitting with the larger 3/8" female threads and push 5 more screens into the threads
Now just assemble the two pieces you have made
Slide on your O-ring and your done
IMPORTANT UPDATE: If you push the screens down further in the threads it works even better and still wont burn the herb even if you try!
Happy Vaping!
Please post your experiences with The Key V2
OPB